Circuit/System Testing
Speaker Malfunction - without Amplifier
- Vehicle OFF, disconnect the harness connector at the appropriate P19 Speaker. Vehicle in Service Mode, radio ON, mute OFF.NOTE: In the following tests, audio signal frequencies (Hz) will be tested. To prevent misdiagnosis, the door chime must be OFF during testing. Ensure the driver door latch is closed during testing.
- Test for 5-7 V between each audio signal circuit terminal 1 and terminal 2 and ground.
- If less than 5 V
- Vehicle OFF, disconnect the X1 harness connector at the A11 Radio.
- Test for infinite resistance between the signal circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance
- Test for less than 2 Ω in the signal circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the A11 Radio.
- If greater than 7 V
- Vehicle OFF, disconnect the X1 harness connector at the A11 Radio. Vehicle in Service Mode.
- Test for less than 1 V between the signal circuit and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- If less than 1 V, replace the A11 Radio.
- If between 5-7 V
- Insert the EL-50334-6 Audio Test CD from the EL-50334-50 USB cable and adapter kit. Play track number three (50 Hz bass test tone) from the test CD.
- Test for 49-51 Hz AC between each signal circuit terminal 1 and terminal 2 and ground.
- If not between 49-51 Hz AC
Replace the A11 Radio.
- If between 49-51 Hz AC
- If not between 49-51 Hz AC
- Test or replace the P19 Speaker.
Speaker Malfunction- with Amplifier
- Vehicle OFF, disconnect the X1 harness connector at the T3 Audio Amplifier.
- Test for less than 10 Ω between the ground circuit terminal 8 and ground.
- If 10 Ω or greater
- Vehicle OFF.
- Test for less than 2 Ω in the ground circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, repair the open/high resistance in the ground connection.
- If less than 10 Ω
- Verify that a test lamp illuminates between the B+ circuit terminal 4 and ground.
- If the test lamp does not illuminate and the circuit fuse is good
- Vehicle OFF.
- Test for less than 2 Ω in the B+ circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, refer to Power Mode Mismatch .
- If the test lamp does not illuminate and the circuit fuse is open
- Vehicle OFF.
- Test for infinite resistance between the B+ circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the T3 Audio Amplifier.
- If the test lamp illuminates
- Disconnect the X2 harness connector at the T3 Audio Amplifier.
- Verify a test lamp does not illuminate between the control circuit terminal 14 and ground.
- If the test lamp illuminates
- Disconnect the X1 harness at the A11 Radio.
- Verify a test lamp does not illuminate between the control circuit and ground.
- If the test lamp illuminates, repair the short to voltage on the circuit.
- If the test lamp does not illuminate, replace the A11 Radio.
- If the test lamp does not illuminate
- Vehicle in Service Mode, A11 Radio ON.
- Verify a test lamp illuminates between the control circuit terminal 14 and ground.
- If the test lamp does not illuminate
- Vehicle OFF. Disconnect the X1 harness at the A11 Radio.
- Test for less than 2 Ω in the control circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the A11 Radio.
- If the test lamp illuminates
- Radio ON, mute ON.
- Test for 7.5-8.5 V between the control circuit terminal 12 and ground.
- If greater than 8.5 V
- Vehicle OFF, disconnect the X1 harness connector at the A11 Radio. Vehicle in Service Mode.
- Test for less than 1 V between the control circuit and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- If less than 1 V, replace the A11 Radio.
- If less than 7.5 V
- Vehicle OFF, disconnect the X1 harness connector at the A11 Radio.
- Test for infinite resistance between the control circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance
- Test for less than 2 Ω in the signal circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the A11 Radio.
- If between 7.5-8.5 V
- Radio ON, mute OFF.
- Test for less than 1 V between the control circuit terminal 12 and ground.
- If greater than 1 V
Replace the A11 Radio.
- If less than 1 V
- If greater than 1 V
- Vehicle OFF, disconnect the X3 harness connector at the T3 Audio Amplifier.
- Vehicle in Service Mode, A11 Radio ON.
- Test for 5-7 V between the signal circuit terminals listed below and ground:
- Left front low level audio signal (+) terminal 14
- Left front low level audio signal (-) terminal 6
- Right front low level audio signal (+) terminal 5
- Right front low level audio signal (-) terminal 13
- Left rear low level audio signal (+) terminal 12
- Left rear low level audio signal (-) terminal 4
- Right rear low level audio signal (+) terminal 3
- Right rear low level audio signal (-) terminal 11
- If less than 5 V
- Vehicle OFF, disconnect the X1 harness connector at the A11 Radio.
- Test for infinite resistance between the signal circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance
- Test for less than 2 Ω in the signal circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the A11 Radio.
- If greater than 7 V
- Vehicle OFF, disconnect the X1 harness connector at the A11 Radio. Vehicle in Service Mode.
- Test for less than 1 V between the signal circuit and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- If less than 1 V, replace the A11 Radio.
- If between 5-7 V
- Insert the EL-50334-6 Audio Test CD from the EL-50334-50 USB cable and adapter kit. Play track number three (50 Hz bass test tone) from the test CD.
- Test for 49-51 Hz AC between the audio signal circuit terminals listed below and ground:
- Left front low level audio signal (+) terminal 14
- Left front low level audio signal (-) terminal 6
- Right front low level audio signal (+) terminal 5
- Right front low level audio signal (-) terminal 13
- Left rear low level audio signal (+) terminal 12
- Left rear low level audio signal (-) terminal 4
- Right rear low level audio signal (+) terminal 3
- Right rear low level audio signal (-) terminal 11
- If not between 49-51 Hz AC
Replace the A11 Radio.
- If between 49-51 Hz AC
- Vehicle OFF, connect all harness connectors.
- Disconnect the harness connector at the appropriate P19 Speaker. Vehicle in Service Mode, A11 Radio ON.
- Test for 5-7 V between the appropriate signal circuit terminals listed below and ground:
- Door speaker or tweeter speaker signal (+): terminal 2
- Door speaker or tweeter speaker signal (-): terminal 1
- Subwoofer speaker signal (+) terminal B
- Subwoofer speaker signal (-) terminal A
- If less than 5 V
- Vehicle OFF, disconnect the X3 harness connector at the T3 Audio Amplifier.
- Test for infinite resistance between the signal circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance
- Test for less than 2 Ω in the signal circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the T3 Audio Amplifier.
- If greater than 7 V
- Vehicle OFF, disconnect the X3 harness connector at the T3 Audio Amplifier. Vehicle in Service Mode.
- Test for less than 1 V between the signal circuit and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- If less than 1 V, replace the T3 Audio Amplifier.
- If between 5-7 V
- Mute OFF, play track number three (50 Hz bass test tone) from the test CD.NOTE: In the following tests, audio signal frequencies (Hz) will be tested. To prevent misdiagnosis, the door chime must be OFF during testing. Ensure the driver door latch is closed during testing.
- Test for 49-51 Hz AC between the appropriate signal circuit terminals listed below and ground:
- Door speaker or tweeter speaker signal (+): terminal 2
- Door speaker or tweeter speaker signal (-): terminal 1
- Subwoofer speaker signal (+) terminal B
- Subwoofer speaker signal (-) terminal A
- If not between 49-51 Hz AC
Replace the T3 Audio Amplifier.
- If between 49-51 Hz AC
- Test or replace the P19 Speaker.