Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Chevrolet >> 2014 >> Traverse LS, 4D Utility >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls And Fuel - 3.6L (LLT) - DTC P0010 To DTC P0336 >> Diagnostic Information and Procedures >> DTC P0101 >> Circuit/System Testing

Circuit/System Testing

NOTE: You must perform Circuit/System Verification  before proceeding with Circuit/System Testing.
  1. Verify the integrity of the entire air induction system by verifying that none of the conditions listed below exist:
    • Any damaged components
    • Improperly installed components
    • Collapsed, restricted or damaged components
    • Loose clamps, cracks or other damage
    • An air flow restriction
    • Restricted air filter
    • Splits, kinks, leaks or improper connections at the vacuum hoses
    • Vacuum leaks at the intake manifold, MAP sensor and throttle body
    • Water intrusion
    • Any snow or ice buildup, in cold climates
    • Contamination of the multifunction intake air sensor element
    • If a condition is found 

      Repair or replace component as appropriate.

    • If no condition is found 
  2. Ignition OFF. Disconnect the harness connector at the B75C Multifunction Intake Air Sensor.
  3. Test for less than 2 Ω between the ground circuit terminal 7 and ground.
    • If 2 Ω or greater 
    1. Disconnect the sensor chassis ground.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 2 Ω 
  4. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 5 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF, remove the test lamp and remove the fuse for the ignition voltage circuit.
    2. Test for less than 2 Ω in the ignition voltage circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF, remove the test lamp and remove the fuse for the ignition voltage circuit.
    2. Test for infinite resistance between the ignition voltage circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, test all components connected to the ignition circuit, replace as necessary.
    • If a test lamp illuminates 
  5. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal 6 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If between 4.8-5.2 V 
  6. Determine if EL-38522-A  Variable Signal Generator or equivalent is available.
    • EL-38522-A, Variable Signal Generator; or equivalent is not available 
    1. Test or replace the B75C Multifunction Intake Air sensor.
    2. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the freeze frame/failure records data.
    3. Verify the DTC does not set.
      • If the DTC sets 

        Replace the K20 Engine Control Module.

      • If no DTCs set 
    4. All OK.
    • EL-38522-A, Variable Signal Generator; or equivalent is available 
  7. Ignition OFF, connect the leads of the EL-38522-A  Variable Signal Generator as listed below:
    • Red lead to the signal circuit terminal 6 at the harness connector
    • Black leads to ground
    • Battery voltage supply lead to B+
  8. Set the EL-38522-A  Variable Signal Generator to the specifications listed below:
    • Signal switch to 5 V
    • Frequency switch to 5 kHz
    • Duty Cycle switch to 50% (Normal)
  9. Engine idling.
  10. Verify the scan tool MAF Sensor parameter is between 4, 950-5, 050 Hz.
    • If not between 4, 950-5, 050 Hz. 

      If not between 4, 950-5, 050 Hz, replace the K20 Engine Control Module.

    • If between 4, 950-5, 050 Hz. 
  11. Test or replace the B75C Multifunction Intake Air Sensor.
scientia non olet · About Mike's Workshop Manuals