Fastener Tightening Specifications
WARNING: This page is about a different car, the 2006 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Carrier Assembly - Differential-to-Transmission Bolts and Nuts | 50 N.m | 37 lb ft |
| Cooler Bolts - Some Models | 10 N.m | 89 lb in |
| Differential Case Bolts | 55 N.m | 41 lb ft |
| Differential Cooler Lower Adapter Nut | 25 N.m | 19 lb ft |
| Differential Cooler Fitting 1/2 Inch | 28 N.m | 21 lb ft |
| Differential Cooler Fitting 3/8 Inch | 18 N.m | 13 lb ft |
| Differential Cooler Mounting Bolts | 10 N.m | 89 lb in |
| Differential Cooler Pump Inlet Hose Retaining Bolt | 10 N.m | 89 lb in |
| Differential Reinforcement Bolt | 30 N.m | 22 lb ft |
| Drain Plug - Quick Connect - Some Models | 35 N.m | 26 lb ft |
| Driveline Support Assembly-to-Engine Flywheel Housing Bolts | 50 N.m | 37 lb ft |
| Electronic Brake and Traction Control Module (EBTCM) LH Mounting Bracket Bolts | 50 N.m | 37 lb ft |
| Fill Plug | 35 N.m | 26 lb ft |
| Left Side Cover Bolts | 30 N.m | 22 lb ft |
| Negative Battery Cable Bolt | 15 N.m | 11 lb ft |
| Pinion Housing/Cage Bolts | 30 N.m | 22 lb ft |
| Pinion Nut | 500 N.m | 370 lb ft |
| Propeller Input Shaft Bearing Positioning Bolts | 35 N.m | 26 lb ft |
| Propeller Shaft Hub Clamp Bolt | 130 N.m | 96 lb ft |
| Quick Connect - Left Cover - Some Models | 18 N.m | 13 lb ft |
| Rear Cover Bolts - Pump Bolts - Some Models | 10 N.m | 89 lb in |
| Rear Suspension Crossmember Mounting Nuts | 110 N.m | 81 lb ft |
| Right Side Cover Bolts | 30 N.m | 22 lb ft |
| Ring Gear Bolts | 145 N.m | 107 lb ft |
| Shift Control Closeout Boot Retaining Nuts | 12 N.m | 106 lb in |
| Shift Control Mounting Bolts | 30 N.m | 22 lb ft |
| Transaxle Mount Bracket-to-Differential Bolts | 50 N.m | 37 lb ft |
| Transaxle Mount-to-Bracket Nuts | 59 N.m | 43 lb ft |
| Transaxle Mount-to-Rear Suspension Crossmember Nuts | 50 N.m | 37 lb ft |
| Transmission Oil Cooler Rear Pipe Fitting-to-Junction Fittings at Engine Flywheel Housing | 27 N.m | 20 lb ft |
| Transmission Shift Rod Clamp Bolt | 30 N.m | 22 lb ft |
| Transmission Stud Mount Bolts | 10 N.m | 89 lb in |
| Transmission Stud-to-Mount | 42 N.m | 31 lb ft |
| Transmission Wiring Harness-to-LH Transmission Case Retaining Bolt | 2.5 N.m | 22 lb in |
| Vehicle Speed Sensor Bolt | 10 N.m | 89 lb in |