Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.

DTC P0068

Step	Action	Value(s)	Yes	No
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module (ECM) Connector End Views or Engine Controls Connector End Views
1	Did you perform the Diagnostic System Check - Vehicle?	-	Go to Step 2	Go to Diagnostic System Check - Vehicle
2	Are DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P1516, P2101, P2119, P2176 also set?	-	Go to Diagnostic Trouble Code (DTC) List - Vehicle	Go to Step 3
3	Observe the Freeze Frame/Failure Records for this DTC. Turn OFF the ignition. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Did the DTC fail this ignition?	-	Go to Step 4	Go to Testing for Intermittent Conditions and Poor Connections
4	Inspect for the following conditions: Vacuum hoses for splits, kinks, and proper connections as shown on the Vehicle Emission Control Information label Any type of leak or restriction Air leaks at the throttle body mounting area and the intake manifold sealing surfaces Restrictions in the air intake system, including the filter Did you find and correct the condition?	-	Go to Step 12	Go to Step 5
5	IMPORTANT: Observe the throttle position (TP) sensors 1 and 2 angle parameter with a scan tool. Start the engine. Apply the accelerator pedal slightly and record the TP 1 and 2 angles. Turn OFF the ignition. Is the difference between the TP sensor 1 angle and the TP sensor 2 angle less than the specified value?	3%	Go to Step 10	Go to Step 6
6	Test the TP sensor 1 5-volt reference circuit for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	-	Go to Step 12	Go to Step 7
7	Test the TP sensor low reference circuit for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	-	Go to Step 12	Go to Step 8
8	Test the TP sensor 1 signal circuit for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	-	Go to Step 12	Go to Step 9
9	Test the TP sensor 2 signal circuit for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	-	Go to Step 12	Go to Step 10
10	Inspect the throttle body for the following conditions: A loose or damaged throttle blade A broken throttle shaft Did you find a condition?	-	Go to Step 11	-
11	Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement?	-	Go to Step 12	-
12	Clear the DTCs with a scan tool. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Did the DTC fail this ignition?	-	Go to Step 3	Go to Step 13
13	IMPORTANT: More than one throttle actuator control (TAC) system-related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Be aware of this when reviewing Captured Info. Observe the Capture Info with a scan tool.Are there any DTCs that have not been diagnosed?	-	Go to Diagnostic Trouble Code (DTC) List - Vehicle	System OK