Test Description

The numbers below refer to the step numbers on the diagnostic table.

2: This step determines if there is a current condition.

Step	Action	Values	Yes	No
1	Did you perform the Diagnostic System Check - Engine Controls?	-	Go to Step 2	Go to Diagnostic System Check - Engine Controls
2	IMPORTANT: The engine may only misfire when the engine is under a load. An engine load may be necessary to verify the condition. Clear the DTCs with a scan tool. Start the engine. Allow the engine to reach operating temperature. Increase the engine speed to the specified value? Did DTCs P0300, or P0301-P0306 set?	1,500 RPM	Go to Step 4	Go to Step 3
3	Observe the Freeze Frame/Failure Records for this DTC. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Did the DTC fail this ignition?	-	Go to Step 4	Go to Diagnostic Aids
4	IMPORTANT: Excessive vibration from other sources than the engine, or a mechanical engine condition can cause a misfire DTC to set. For example, an accessory drive belt could cause this condition. Is the engine misfiring?	-	Go to Step 5	Go to Symptoms - Engine Mechanical in Engine Mechanical-2.5L (LBK)
5	Observe the DTC Info with a scan tool. Is DTC P0101, P0102, P0103, P0106, P0107, P0108, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P0335, P0336, P0337, P0341, P0342, P0351-P0356, P1320, or P1321 also set?	-	Go to Diagnostic Trouble Code (DTC) List	Go to Step 6
6	Is there an engine mechanical noise?	-	Go to Symptoms - Engine Mechanical in Engine Mechanical-2.5L (LBK)	Go to Step 7
7	Is there more than one misfire DTC set?	-	Go to Step 8	Go to DTC P0301-P0306
8	Is there any HO2S DTCs set?	-	Go to Diagnostic Trouble Code (DTC) List	Go to Step 9
9	Inspect or test for the following conditions: Inspect the vacuum hoses for splits, kinks, and proper connections. Inspect the throttle body and the intake manifold for vacuum leaks. Inspect the crankcase ventilation valve and/or system for any vacuum leaks. Test for the correct fuel pressure. Refer to Fuel System Diagnosis . Inspect the fuel system for any restrictions, leaks or fuel contamination. Refer to Fuel System Diagnosis or Alcohol/Contaminants-in-Fuel Diagnosis (WO/Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (W/Special Tool) . Inspect for fouled or damaged spark plugs. Determine what caused the spark plugs to foul. Refer to Spark Plug Inspection . Inspect the exhaust system for restrictions. Refer to Restricted Exhaust in Engine Exhaust. Inspect the engine control grounds for being clean, tight, and in the correct location. Repair as necessary. Did you find and correct the condition?	-	Go to Step 10	Go to Symptoms - Engine Mechanical in Engine Mechanical-2.5L (LBK)
10	Clear the DTCs with a scan tool. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Did the DTC fail this ignition?	-	Go to Step 2	Go to Step 11
11	Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed?	-	Go to Diagnostic Trouble Code (DTC) List	System OK