Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Cadillac >> 2016 >> CTS Base, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 17 (Engine Mechanical - 6.2L (LT4)) >> Specifications >> Fastener Specifications

Fastener Specifications

WARNING: This page is about a different variant/trim than selected.
Application Specification
Metric English
Accessory Drive Belt Tensioner Bolt - Lower 22 N.m 16 lb ft
Accessory Drive Belt Tensioner Pulley Bolt 58 N.m 43 lb ft
Supercharger Belt Idler Pulley Bolts - All 58 N.m 43 lb ft
Automatic Transmission Flex Plate Bolts (1)
  • First Pass
 15 N.m 11 lb ft
  • Second Pass
 30 N.m 22 lb ft
  • Final Pass
 45 degrees
Flywheel Bolts (1)
  • First Pass
 15 N.m 11 lb ft
  • Second Pass
 30 N.m 22 lb ft
  • Final Pass
 45 degrees
Camshaft Position (CMP) Actuator Magnet Bolts 10 N.m 89 lb in
Camshaft Position (CMP) Actuator Solenoid Valve (1)
  • First Pass
 65 N.m 48 lb ft
  • Final Pass
 90 degrees
Camshaft Position (CMP) Sensor Bolt 25 N.m 18 lb ft
Camshaft Position (CMP) Sensor Wire Harness Bolt 25 N.m 18 lb ft
Camshaft Retainer Bolts - TORX Head Bolts 15 N.m 11 lb ft
Connecting Rod Bolts (1)
  • First Pass
 20 N.m 15 lb ft
  • Final Pass
 85 degrees
Coolant Temperature Sensor 20 N.m 15 lb ft
Crankshaft Balancer Bolt - Installation Pass with Used Bolt - to Ensure the Balancer is Completely Installed 330 N.m 243 lb ft
Crankshaft Balancer Bolt New Bolt with Flanged Head (1)
  • First Pass
 150 N.m 111 lb ft
  • Second Pass
 Loosen 360 degrees
  • Third Pass
 80 N.m 59 lb ft
  • Final Step
 125 degrees
Crankshaft Balancer Bolt New Bolt with Retained Rotating Washer (1)
  • First Pass
 150 N.m 111 lb ft
  • Second Pass
 Loosen 360 degrees
  • Third Pass
 80 N.m 59 lb ft
  • Final Step
 200 degrees
Crankshaft Bearing Cap Bolts (1)
  • Inner Bearing Cap Bolts - First Pass in Sequence1
 20 N.m 15 lb ft
  • Inner Bearing Cap Bolts - Final Pass in Sequence1
 110 degrees
  • Outer Bearing Cap Bolts - First Pass in Sequence
 20 N.m 15 lb ft
  • Outer Bearing Cap Bolts - Final Pass in Sequence
 80 degrees
  • Bearing Cap Side Bolts - First Pass in Sequence
 25 N.m 18 lb ft
  • Bearing Cap Side Bolts - Final Pass in Sequence
 60 degrees
Crankshaft Oil Deflector Bolts 10 N.m 89 lb in
Crankshaft Position (CKP) Sensor Bolt 25 N.m 18 lb ft
Crankshaft Rear Oil Seal Housing Bolts 25 N.m 18 lb ft
Cylinder Head Bolts (1)
  • Cylinder Head Bolts - Internal Hex - LH Cylinder Head forward most fastener - First Pass in Sequence
 80 N.m 59 lb ft
  • Cylinder Head Bolts - Internal Hex - LH Cylinder Head forward most fastener - Second Pass in Sequence
 90 degrees
  • Cylinder Head Bolts - Internal Hex - LH Cylinder Head forward most fastener - Final Pass in Sequence
 40 degrees
  • Cylinder Head Bolts - Standard Hex - First Pass in Sequence
 80 N.m 59 lb ft
  • Cylinder Head Bolts - Standard Hex - Second Pass in Sequence
 90 degrees
  • Cylinder Head Bolts - Standard Hex - Final Pass in Sequence
 60 degrees
Engine Block Coolant Drain Hole Plug 60 N.m 44 lb ft
Engine Block Coolant Heater 50 N.m 37 lb ft
Engine Block Oil Gallery Plugs - Front 25 N.m 18 lb ft
Engine Block Oil Gallery Plugs - Rear 30 N.m 22 lb ft
Engine Oil Cooler Adapter to Oil Pan Bolt (M6) 10 N.m 89 lb in
Engine Oil Cooler Adapter to Oil Pan Bolt (M8) 25 N.m 18 lb ft
Engine Oil Cooler Coolant Fitting 35 N.m 26 lb ft
Engine Oil Cooler Core Bolt 25 N.m 18 lb ft
Engine Mount Fastener (1) 58 N.m 43 lb ft
Engine Wiring Harness Bolt (Rear Engine Channel) 10 N.m 89 lb in
Engine Wiring Harness Jumper Bracket Bolt 25 N.m 18 lb ft
Exhaust Manifold Bolts
  • Exhaust Manifold Bolts- If installing on existing cylinder head
 23 N.m 17 lb ft
  • Exhaust Manifold Bolts- If installing on NEW cylinder head
 27 N.m 20 lb ft
Exhaust Manifold Heat Shield Bolts 10 N.m 89 lb in
Front Cover Bolts 25 N.m 18 lb ft
Low Pressure Fuel Feed Pipe to Rocker Arm Cover Bolt 10 N.m 89 lb in
Fuel Pump Bolts 25 N.m 18 lb ft
High Pressure Fuel Feed Pipe Fittings (1) 28 N.m 21 lb ft
Low Pressure Fuel Feed Pipe to Rocker Arm Cover Bolt 10 N.m 89 lb in
Fuel Injection Fuel Rail Bolts 25 N.m 18 lb ft
Fuel Injection Fuel Rail Crossover Pipe Bolt 10 N.m 89 lb in
Generator Bracket Bolts 50 N.m 37 lb ft
Ignition Coil Bracket-to-Valve Rocker Arm Cover Bolts 10 N.m 89 lb in
Intake Manifold Bolts
  • First Pass in Sequence
 5 N.m 44 lb in
  • Final Pass in Sequence
 10 N.m 89 lb in
Intake Manifold Cover Studs 4.5 N.m 40 lb in
Intake Manifold Cover Bolts 4.5 N.m 40 lb in
Knock Sensor Bolts 25 N.m 18 lb ft
Knock Sensor Heat Shield Bolt 25 N.m 18 lb ft
Oil Filter 3/4 to 1 full turn after gasket makes contact with the sealing surface on the filter mounting flange
Oil Filter Fitting 55 N.m 41 lb ft
Oil Level Indicator Tube Bolt 10 N.m 89 lb in
Oil Pan Cover Bolts 10 N.m 89 lb in
Oil Pan Drain Plug 25 N.m 18 lb ft
Oil Pan Bolts - Oil Pan-to-Rear Housing 12 N.m 106 lb in
Oil Pan Bolts - Oil Pan-to-Rear Housing 12 N.m 106 lb in
Oil Pan Bolts - Oil Pan-to-Engine Block and Oil Pan-to-Front Cover 25 N.m 18 lb ft
Oil Pressure Sensor 35 N.m 26 lb ft
Oil Level Sensor Bolts 10 N.m 89 lb in
Oil Pump Screen Bolts 10 N.m 89 lb in
Oil Pump-to-Engine Block Bolts 25 N.m 18 lb ft
Positive Crankcase Ventilation Valve 10 N.m 89 lb in
Positive Crankcase Ventilation Oil Separator Bolt 10 N.m 89 lb in
Positive Crankcase Ventilation Oil Separator Drain Tube Bolt 25 N.m 18 lb ft
Positive Crankcase Ventilation Oil Separator Drain Tube Check Valve 35 N.m 26 lb ft
Spark Plugs 20 N.m 15 lb ft
Supercharger Belt Idler Pulley Bracket Bolts 25 N.m 18 lb ft
Charge Air Cooler Cover Bolts
  • First Pass in Sequence
 10 N.m 89 lb in
  • Final Pass in Sequence (Fasteners 1 thru 8 only)
 10 N.m 89 lb in
Supercharger to Block Bolts
  • First Pass in Sequence
 10 N.m 89 lb in
  • Final Pass in Sequence
 10 N.m 89 lb in
Supercharger Water Manifold Bolts 10 N.m 89 lb in
Charge Air Regulator Solenoid Valve Bolt 10 N.m 89 lb in
Supercharger Bypass Valve Actuator Bolt 27 N.m 20 lb ft
Map Sensor Bolt - Supercharger 10 N.m 89 lb in
Supercharger Inlet Air Pressure and Temperature Sensor Bolt 10 N.m 89 lb in
Throttle Body Bolts 10 N.m 89 lb in
Map Sensor Bolt - Intake Manifold 4.5 N.m 40 lb in
EVAP Purge Valve Bolt 10 N.m 89 lb in
Timing Chain Tensioner Bolts 25 N.m 18 lb ft
Valve Lifter Guide Bolts 12 N.m 106 lb in
Valve Lifter Follower Guide Bolt 12 N.m 106 lb in
Valve Lifter Oil Manifold Bolts
  • First Pass in Sequence
 15 N.m 11 lb ft
  • Final Pass in Sequence
 30 N.m 22 lb ft
Valve Lifter Oil Manifold Filter Plug 30 N.m 22 lb ft
Valve Rocker Arm Bolts 30 N.m 22 lb ft
Valve Rocker Arm Cover Bolts - In Sequence 10 N.m 89 lb in
Water Outlet Housing Bolts 10 N.m 89 lb in
Water Pump Impeller Bolts 10 N.m 89 lb in
Engine Coolant Manifold Bolts 25 N.m 18 lb ft
Starter Heat Shield Bolt - Side 10 N.m 89 lb in
Starter Heat Shield Bolt - Rear 25 N.m 18 lb ft
1. Use NEW fastener.
scientia non olet · About Mike's Workshop Manuals