Installation Procedure

WARNING: This page is about a different car, the 2010 GMC Sierra and 2010 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: View Of EBCM

Courtesy of GENERAL MOTORS CORP.

Install the EBCM (1) to the BPMV, if removed.

Fig 2: View Of EBCM Bolts

Courtesy of GENERAL MOTORS CORP.

CAUTION: Refer to Fastener Caution .

Install the EBCM bolts (1) and tighten in a cross pattern to 3 N.m (27 lb in).

Fig 3: Identifying Brake Pressure Modulator Valve (BPMV) Bracket

Courtesy of GENERAL MOTORS CORP.

Install the sleeves and insulators to the BPMV, if removed.
Install the BPMV assembly to the bracket (1).

Fig 4: View Of Brake Pressure Modulator Valve (BPMV)

Courtesy of GENERAL MOTORS CORP.

Install the BPMV bolts (1) and tighten to 9 N.m (80 lb in).

Fig 5: View Of Hydraulic Control Unit & Bracket Assembly

Courtesy of GENERAL MOTORS CORP.

Position the hydraulic control unit and bracket assembly (1) to the frame rail. Slide the assembly toward the left of the vehicle and install the assembly to the vehicle frame.

Fig 6: View Of Brake Pressure Modulator Valve (BPMV) Bracket & Bolts

Courtesy of GENERAL MOTORS CORP.

Through the frame crossmember, install the BPMV bracket bolts (1) and tighten to 22 N.m (16 lb ft).

Fig 7: Identifying Brake Pressure Modulator Valve (BPMV) Bracket Bolt

Courtesy of GENERAL MOTORS CORP.

Tighten the lower BPMV bracket bolt (1) to 22 N.m (16 lb ft).

Fig 8: Identifying Right Supply Brake Pipe

Courtesy of GENERAL MOTORS CORP.

Connect the right supply brake pipe fitting (1) and tighten to 18 N.m (13 lb ft).
Connect the left supply brake pipe fitting (2) and tighten to 18 N.m (13 lb ft).

Fig 9: View Of Primary Brake Pipe Fitting

Courtesy of GENERAL MOTORS CORP.

Connect the primary brake pipe fitting (1) and tighten to 18 N.m (13 lb ft).

Fig 10: View Of Right Rear Brake Pipe Fitting

Courtesy of GENERAL MOTORS CORP.

Connect the right rear brake pipe fitting (1) and tighten to 18 N.m (13 lb ft).
Connect the left rear brake pipe fitting (2) and tighten to 18 N.m (13 lb ft).

Fig 11: View Of BPMV Return Hose Quick Connect Fitting

Courtesy of GENERAL MOTORS CORP.

Connect the BPMV return hose quick connect (1).
Ensure the return hose quick connect is fully engaged by attempting to pull the return hose from the outlet fitting.

Fig 12: Identifying BPMV Supply Hose Quick Connect Fitting

Courtesy of GENERAL MOTORS CORP.

Connect the BPMV supply hose quick connect (1).
Ensure the supply hose quick connect is fully engaged by attempting to pull the supply hose from the inlet fitting.
Connect the EBCM electrical connector.

Fig 13: View Of Brake Modulator Manual Pressure Relief Valve

Courtesy of GENERAL MOTORS CORP.

Tighten the brake modulator manual pressure relief valve (1) to 40 N.m (30 lb ft).

Fig 14: Identifying ABS Module Splash Shield

Courtesy of GENERAL MOTORS CORP.

Install the ABS module splash shield (1).

Fig 15: Identifying ABS Module Splash Shield Bolts

Courtesy of GENERAL MOTORS CORP.

Install the ABS module splash shield bolts (1) and tighten to 20 N.m (15 lb ft).

Fig 16: Identifying Antilock Brake System (ABS) Module Splash Shield Retainer

Courtesy of GENERAL MOTORS CORP.

Install the ABS module splash shield retainer (1).
If installing a new EBCM, the EBCM must be programmed. Refer to Control Module References .
Perform the Antilock Brake System Automated Bleed .
Follow the procedure completely to ensure the sensor and boost valve calibration and EBCM learn processes have been completed.