Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Cadillac >> 2005 >> DeVille Protection Series >> Repair and Diagnosis >> Brakes >> Antilock Brake System, Traction Control System & Stability Control System >> Diagnostic Information and Procedures >> DTC C1282 >> Test Description

Test Description

The number below refers to the step number on the diagnostic table.

  1. 3:  This step tests for the proper operation of the circuit in the low voltage range.
  2. 4:  This step tests for the proper operation of the circuit in the high voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to ground.
  3. 5:  This step tests for a short to voltage in the 5-volt reference circuit.
  4. 6:  This step tests the bias voltage of the yaw rate sensor.
DTC C1282

Step Action Values Yes No
Schematic Reference: ABS Schematics 
Connector End View Reference: ABS Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Yaw Rate Sensor Input parameter in the VSES data list.
Does the scan tool display that the Yaw Rate Sensor Input parameter is within the specified range?		 0.15-4.85 V Go to Step 6  Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the yaw rate sensor connector.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the Yaw Rate Sensor Input parameter.
Does the scan tool display that the Yaw Rate Sensor Input parameter is less than the specified value?		 0.15 V Go to Step 4  Go to Step 10 
4 
  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the yaw rate sensor and the signal circuit of the yaw rate sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the Yaw Rate Sensor Input parameter.
Does the scan tool display that the Yaw Rate Sensor Input parameter is greater than the specified value?		 4.85 V Go to Step 5  Go to Step 8 
5 
  1. Disconnect the fused jumper wire.
  2. Measure the voltage between the 5-volt reference circuit of the yaw rate sensor and the low reference circuit of the yaw rate sensor.
Does the voltage measure less the specified value?		 5 V Go to Step 12  Go to Step 7 
6  Does the scan tool display that the Yaw Rate Sensor Input parameter is within the specified range? 2.3-2.7 V Go to Diagnostic Aids Go to Step 11 
7 Test the 5-volt reference circuit of the yaw rate sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 13 
8 Test the 5-volt reference circuit of the yaw rate sensor for the following conditions:
  • An open
  • A short to ground
  • A high resistance

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 9 
9 Test the signal circuit of the yaw rate sensor for the following conditions:
  • An open
  • A short to ground
  • A high resistance

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 13 
10 Test the signal circuit of the yaw rate sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 13 
11
  1. Disconnect the electronic brake control module (EBCM) harness connector.
  2. Install the J 39700 Universal Pinout Box using the J 39700-300  Cable Adapter to the EBCM harness connector only. See Special Tools .
  3. Test the low reference circuit of the yaw rate sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 12 
12 Inspect for poor connections at the harness connector of the yaw rate sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 14 
13 Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 15 
14 Replace the yaw rate sensor. Refer to Yaw Rate Sensor Replacement .
Did you complete the replacement?		 - Go to Step 16  -
15 Replace the EBCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 16  -
16
  1. Clear the DTCs using the scan tool.
  2. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.
Does the DTC reset?		 - Go to Step 2  System OK
scientia non olet · About Mike's Workshop Manuals