Engine Control Module --, 2016 MY

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Audi A3 Quattro, 2017 Audi A3, 2016 Audi A3 Quattro, 2016 Audi A3, and 2015 Audi A3 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

DTC / Description	Monitor Strategy Description	Malfunction Criteria and Threshold Value	Secondary Parameters with Enable Conditions	Monitoring Time Length	MIL Illum.	Component Diagnostic Procedure
P000A "A" Camshaft Position Slow Response Bank 1	VVT Actuator Intake Rationality Check	Adjustment angle difference >= 1.00; < 10.0° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Set point change > 20.0° CRK Dynamic diagnosis timer >= 0.95 - 4.0 s	0 FTP75: 300 s Continuous	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 -N205-, CHECKING .
P000B "B" Camshaft Position Slow Response Bank 1	Variable Valve Timing (VVT) Exhaust Actuator rationality check	Adjustment angle difference>= 1.00; < 3.50° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Set point change > 6.0° CRK Dynamic diagnosis timer >= 0.95 - 4.0 s	0 FTP75: 700 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 -N318-, CHECKING
P0010 "A" Camshaft Position Actuator Control Circuit/Open Bank 1	VVT Actuator Intake Open Circuit	Output voltage lower range 1.92 - 2.21 V Output voltage upper range (hardware values) 2.85 - 3.25 V	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 -N205-, CHECKING .
P0011 "A" Camshaft Position - Timing Over-Advanced or System Performance Bank 1	VVT Actuator Intake Rationality Check	Camshaft position deviation > 10.0° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Camshaft position n.a. Camshaft position adjustment active Catalyst heating not active Camshaft position deviation integrator (actual vs. setpoint position) >= 9.00 - 12.00° CRK	0 FTP75: 250 s Continuous	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 -N205-, CHECKING .
P0013 "B" Camshaft Position Actuator Control Circuit/Open Bank 1	Variable Valve Timing (VVT) Exhaust Actuator open circuit	Output voltage, lower range1.92 - 2.21 V Output voltage, upper range2.85 - 3.25 V (hardware values)	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 -N318-, CHECKING
P0014 "B" Camshaft Position - Timing Over-Advanced or System Performance Bank 1	Variable Valve Timing (VVT) Exhaust Actuator Rationality Check	Difference between target and actual position> 10.00° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Camshaft position n.a. Camshaft position adjustment active Catalyst heating not active Camshaft position deviation integrator (actual vs. setpoint position) >= 9.00 - 12.00° CRK	0 FTP75: 450 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 -N318-, CHECKING
P0016 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A	Camshaft Position/Crankshaft Position Intake - Correlation Adaptation Value Monitoring	Adapted value for each edge of the target wheel < -14.0° CRK Or Adapted value for each edge of the target wheel > 14.0° CRK	Camshaft position adaptation active (Exhaust side) Engine speed 288 - 4, 000 rpm Modeled oil temperature >= -15° C Modeled oil temperature <= 160° C Diff. actual exhaust camshaft position vs. previous camshaft position @ reference signal edge < 2.00° CRK And Case 1: Ignition off Engine speed > 380 rpm Engine stalling >= 1.0 s Or Case 2: Engine speed >= 380 rpm Or Engine running Engine stalling>= 5.0s Or Case 3: Backwards rotationnot detected Or Case 4: Engine speed>= 400rpm Enginestopped	720° CRK Multiple	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 -N205-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor -G28-, CHECKING .
Diff. actual camshaft adaptation per cylinder vs. previous reference camshaft adaptation >= 12.00° CRK			General: Camshaft phasing commanded Engine speed < 8, 160 rpm Diff. actual intake camshaft position vs. previous camshaft position @ reference signal edge < 2.00° CRK Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Case 2: synchronization test incorrect Or Engine running And Engine stalling >= 5.0 s Case 3: Backwards rotation not detected Or Case 4: Engine speed >= 400 RPM Engine stopped	0.1 s Continuous
P0017 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B	Camshaft Position/Crankshaft Position Exhaust - Correlation Adaptation Value Monitoring	Adapted value for each edge of the target wheel < -14.0° CRK Or Adapted value for each edge of the target wheel > 14.0° CRK	Camshaft position adaptation active (Exhaust side) Modeled oil temperature >= -15° C Modeled oil temperature <= 160° C Engine speed 288 - 4, 000 RPM Diff. actual exhaust camshaft position vs. previous camshaft position @ reference signal edge < 2.0° CRK And Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Case 2: Engine speed >= 380 RPM Or Engine running And Engine stalling >= 5.0 s Or Case 3: Backwards rotation not detected Or Case 4: Engine speed >= 400 RPM Engine stopped	720° CRK Multiple	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 -N318-, CHECKING -- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor -G28-, CHECKING .
P0030 HO2S Heater Control Circuit Bank 1 Sensor 1	Oxygen Sensors Heater Front Open Circuit	O2S upstream heater voltage lower range 1.92 - 2.21 V O2S downstream heater voltage upper range 2.85 - 3.25 V		2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P0031 HO2S Heater Control Circuit Low Bank 1 Sensor 1	Oxygen Sensors Heater Front Short To Ground	O2S upstream heater voltage lower range 1.92 - 2.21 V		2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P0032 HO2S Heater Control Circuit High Bank 1 Sensor 1	Oxygen Sensors Heater Front Short To Battery Voltage	O2S upstream heater driver temperature > 160.0 - 200.0° C Or O2S upstream heater driver output current driver stage internal value	EGT @ O2S front >= -273° C Actuator commanded on	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P0033 Turbocharger/Supercharger Bypass Valve "A" Control Circuit	Turbocharger Bypass (TCBY) open circuit	Voltage, lower range1.92 - 2.21V Voltage, upper range2.85 - 3.25V (hardware values)	Actuatorcommanded off	1.0 s Continuous	2 DCY	-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve -N249-, CHECKING
Turbocharger Bypass (TCBY) short to battery plus		Currentdriver stage internal value Or Temperature> 160 - 200° C (hardware values)	Actuatorcommanded on
P0034 Turbocharger/Supercharger Bypass Valve "A" Control Circuit Low	Turbocharger Bypass (TCBY) short to ground	Voltage< 1.92 - 2.21V (hardware values)	Actuatorcommanded off	1.0 s Continuous	2 DCY	-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve -N249-, CHECKING
P0036 HO2S Heater Control Circuit Bank 1 Sensor 2	Oxygen Sensors Heater Rear Open Circuit	O2S downstream heater voltage lower range 1.92 - 2.21 V O2S downstream heater voltage upper range 2.85 - 3.25 V	Engine not in start process	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0037 HO2S Heater Control Circuit Low Bank 1 Sensor 2	Oxygen Sensors Heater Rear Short To Ground	O2S downstream heater voltage 1.92 - 2.21 V	Engine not in start process	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0038 HO2S Heater Control Circuit High Bank 1 Sensor 2	Oxygen Sensors Heater Rear Short To Battery Voltage	O2S downstream heater driver temperature > 160.0 - 200.0° C Or O2S downstream heater driver output current driver stage internal value	EGT @ O2S rear (binary) >= -273 Actuator commanded on Engine not in start process	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0045 Turbocharger/Supercharger Boost Control "A" Circuit/Open	Turbocharger Boost Pressure Control Valve Open Circuit	Bypass valve driver load resistance > 200 kOhm	Deviation between actual and filtered boost pressure actuator position <= 5.0 % Boost pressure actuator controller not active Time delay > 1.0 s	0.4 s Continuous	2 DCY	-- Check the Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-. Refer to Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-, CHECKING .
P0068 MAP/MAF - Throttle Position Correlation	Leak to Intake Manifold Rationality Check	Difference between target intake manifold pressure and actual intake manifold pressure < -15.0 - -10.0 kPa	Time after engine start > 5.0 s Barometric pressure > 73.0 - 105.0 kPa Engine speed > 576 - 512 RPM Engine speed < 3, 000 RPM IAT @ intake manifold > -48° C ECT @ cylinder head > -48° C Difference between engine speed and filtered engine speed < 8, 160 RPM Diff. air mass setpoint vs. filtered air mass setpoint for load dynamic detection< 25.01 mg/rev Throttle actuator commanded on Modeled pressure quotient 0.10 - 0.60 [-] Gradient of intake manifold pressure >= -199.90; <= 199.90 kPa/s Vehicle speed <= 1 mph	5.0 s Continuous	2 DCY	-- Check the Intake system for vacuum leaks, make sure oil dipstick is pushed properly into place.-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
Intake Air System Rationality Check		General conditions: Filtered lambda controller included correction and adaption -30.00 - 30.00 % Lambda control active And Deviation throttle area controller < -60.00 %	General conditions: Throttle position> 0.000° TPS Throttle position< 100.003° TPS Engine speed> 576; < 3008rpm Modeled pressure quotient> 0.27; < 0.57[-] Enginerunning Throttle actuatorcommanded on Time after engine start> 5.0 s Throttle positionsensor failure not detected Fuel cut offnot active Fast throttle adaptationfinished MAP gradient-199.90 - 199.90 kPa/s BARO plausibility diagnosisfinished Intake manifold modeled adaptation active And Choice of: MAF sensoractive Or MAP sensor active And Choice of: Pressure upstream throttle< 135.00kPa Or Pressure upstream throttlenot active And Choice of: BARO> 73.00; < 107.50 kPa Or Barometric pressure sensor not active
P0070 Ambient Air Temperature Sensor Circuit "A"	CAN: Ambient Air Temperature Sensor Short To Battery Voltage Or Open Circuit	AAT sensor voltage (hardware values) > 4.50 V		2.0 s Continuous	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor -G17-, CHECKING .
P0071 Ambient Air Temperature Sensor Circuit "A" Range/Performance	Ambient Air Temperature Sensor Cross Check	High side: Diff. AAT @ cold start vs. IAT @ manifold @ cold start > 25 K Diff. AAT @ cold start vs. ECT @ radiator outlet @ cold start > 25 K Min. amount of faulty reference measurements to detect defective sensor 2.00 [-] Or Low side: Diff. IAT @ manifold @ cold start vs. AAT @ cold start > 25.0 K Diff. ECT @ radiator outlet @ cold start vs. AAT @ cold start > 25.0 K Min. amount of faulty reference measurements to detect defective sensor 2.00 [-]	Engine off time >= 360.0 min Engine off time plausible Time after engine start < 1, 400.0 s Depending on temperature slope: Diff. actual vs previous IAT < 256.0 K Diff. actual vs previous ECT @ cylinder head n.a. K Diff.. actual vs previous ECT@ radiator outlet < 256.0 K Diff. actual vs previous AAT < 256.0 K For time >= 1.0 s Depending on meanvalue condition Mean value of all temperature sensors @ cold start>= -256° C Number of valid sensors>= 2.00[-] Depending on block heater / solar radiation detection Time after engine start>= 0.5s Vehicle speed>= 22 mph For time>= 20.0 s Diff. actual IAT @ manifold vs. min. IAT @ manifold< 5.0 K Diff. actual ECT @ cylinder head vs. min. ECT @ cylinder headn.a.K Diff. actual AAT vs. min. AAT< 4.0 K Diff. actual ECT @ radiator outlet vs. min. ECT @ radiator outlet< 1.1 K	0.1 s Once / DCY	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor -G17-, CHECKING .
P0072 Ambient Air Temperature Sensor Circuit "A" Low	CAN: Ambient Air Temperature Sensor Short To Ground	AAT sensor voltage < 0.10 V		2.0 s Continuous	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor -G17-, CHECKING .
P0087 Fuel Rail/System Pressure - Too Low Bank 1	Fuel System Pressure Sensor, High Pressure Side Out Of Range Low	Deviation lambda of controller included adaptation -50.0 - 50.0 % And High pressure controller output > 45 mg And Deviation between fuel pressure set point and current fuel pressure > 2, 999.80 kPa Fuel pressure > 3, 500.31 kPa	General: Engine speed608 - 6, 816[rpm] Fuel mass setpoint5.00 - 1, 389.00mg/rev Time after engine start> 10.0 s Engine warm-upnot calibrated Catalyst heatingnot calibrated Full loadnot calibrated Catalyst purgenot calibrated Lambda controlnot calibrated Evap purge functionality diagnosisnot calibrated Fuel pressure setpoint gradient<= 34, 777.60kPa And Depending on low dynamic conditions: Fuel mass setpoint lower range> 5.00mg/rev For time >= 10.0 s Fuel mass setpoint upper range< 187.17 - 229.23mg/rev Fuel mass setpoint gradient-1389.00 - 1389.00mg/rev For time>= 5.0s And Depending on canister purge: Canister loadnot calibrated[-] Or Evap purge valve not calibrated	5.0 s Continuous	2 DCY	-- Check the fuel pressure, refer to the repair information for proper procedures.-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Pressure Regulator Valve -N276-, CHECKING .-- Check the Fuel Pump Control Module -J538- / Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .
P0090 Fuel Pressure Regulator 1 Control Circuit/Open	Fuel Volume Regulator Control open circuit	Voltage high side< 1.87 - 2.26V Voltage low side> 2.78 - 3.33V	Engine speed> 600 rpm And Fuel cut offnot active Actuator commanded on	0.8 s Continuous	2 DCY	-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Pressure Regulator Valve -N276-, CHECKING .
					Low and high side Off: Voltage low side> 2.78 - 3.33V Voltage high side< 1.87 - 2.26V Low and high side On: Current low sidedriver stage internal value Current high sidedriver stage internal value
P0091 Fuel Pressure Regulator 1 Control Circuit Low	Fuel Volume Regulator Control short to ground (high side)	Current high sidedriver stage internal value (hardware values)	Ignitionon Or Ignitionoff (during ECM keep alive-time) And Actuatorcommanded on	0.8 s Continuous	2 DCY	-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Pressure Regulator Valve -N276-, CHECKING .
Fuel Volume Regulator Control short to ground (low side)		Voltage low side< 1.87 - 2.26V (hardware values)	Ignitionon Or Ignitionoff (during ECM keep alive-time) And Actuatorcommanded off
P0092 Fuel Pressure Regulator 1 Control Circuit High	Fuel Control Valve Short To Battery Plus (Low Side)	Current low side (hardware values) driver stage internal value	Ignition on Or Ignition off (during ECM keep alive-time) And Actuator commanded on	0.8 s Continuous	2 DCY	-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Pressure Regulator Valve -N276-, CHECKING .
Fuel Control Valve Short To Battery Plus (High Side)		Voltage high side (hardware values) < 2.78 - 3.33 V	Ignition on Or Ignition off (during ECM keep alive-time) And Actuator commanded off
P00B7 Engine Coolant Flow Low/Performance	Rotary Coolant Valve Functional Check	Diff. previous and actual position of RVC < 4.0°	ECT @ cylinder head > 11° C RCV position 0.00 - 270.0° Diff. previous actual and target position of RCV > 5.0° And RCV adaptation finished Or RCV adaptation not active	3.0 s Continuous	2 DCY	-- Check coolant system for leaks or damage.-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator -N493-, CHECKING ..
P0106 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance	Manifold Pressure Sensor By Engine Standing: Rationality Check During ECM Keep Alive-Time:	Case 1: Diff. barometric pressure vs. intake manifold pressure>= 8.50 kPa Diff. upstream throttle pressure vs. intake manifold pressure> 8.50 kPa Diff. barometric pressure vs. upstream throttle pressure< 8.50 kPa Case 2: Intake manifold pressure (raw value)< 25.00; > 125.00kPa Case 3; Diff. barometric pressure vs. intake manifold pressuren.a. kPa Diff. upstream throttle pressure vs. intake manifold pressuren.a. kPa Diff. barometric pressure vs. upstream throttle pressuren.a.kPa Diff. intake manifold pressure vs. intake manifold pressure @ idle or low part loadn.a.kPa Case 4: Diff. barometric pressure vs. intake manifold pressuren.a. kPa Diff. upstream throttle pressure vs. intake manifold pressuren.a. kPa Diff. barometric pressure vs. upstream throttle pressuren.a. kPa Diff. intake manifold pressure vs. intake manifold pressure @ idle or low part loadn.a. kPa	Enginestopped Ignitionoff Vehicle speed< 1 mph ECM keep alive time> 10.0 s Delay time after engine stop>= 5.0 s Barometric pressure sensor voltage0.20 - 4.80 V MAP sensor voltage0.20 - 4.80 V Turbocharger boost pressure sensor voltage0.20 - 4.80 V	3.0 s Once / DCY	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .
Intake Air System Rationality Check		General conditions: Filtered lambda controller included correction and adaption < -30.0 % And Deviation throttle area controller > 45.0 %	Throttle position > 0.0° TPS Throttle position < 100.003° TPS Engine speed > 576; < 3008 RPM Modeled pressure quotient > 0.27; < 0.57 [-] Engine running Throttle actuator commanded on Time after engine start > 5.0 s Throttle position sensor failure not detected Fuel cut off not active Fast throttle adaptation finished Gradient intake manifold pressure -199.90 - 199.90 kPa/s Barometric pressure plausibility diagnosis finished Intake manifold modeled adaptation active And Choice of: MAF sensor active Or Manifold pressure sensor active And Choice of: pressure upstream throttle< 135.00 kPa Or Pressure upstream throttlenot active And Choice of: BARO> 73.00; < 107.50[kPa] Or Barometric pressure sensornot active	5.0 s Continuous
					General conditions: Filtered lambda controller included correction and adaption > 30.0 % And Deviation throttle area controller < -45.0 %
P0107 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low	Manifold Pressure Sensor Short To Ground	Intake manifold pressure sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .
P0108 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High	Manifold Pressure Sensor Short To Battery Voltage	Intake manifold pressure sensor voltage > 4.80 V		0.5 s Continuous	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .
P0111 Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1	Intake Air Temperature Sensor @ Manifold Cross Check	High side: reference measuring Diff. IAT @ manifold @ cold start vs. AAT @ cold start> 25.0K Diff. IAT @ manifold @ cold start vs. ECT @ cylinder head @ cold start n.a. K Diff. IAT @ manifold @ cold start vs. ECT @ radiator outlet @ cold start> 25.0 K Min. amount of faulty reference measurements to detect defective sensor2.00[-] Or Low side: reference measuring Diff. AAT @ cold start vs. IAT @ manifold @ cold start> 25.0 K Diff. ECT @ cylinder head @ cold start vs. IAT @ manifold @ cold start> 25.0 K Diff. ECT @ radiator outlet @ cold start vs. IAT @ manifold @ cold start> 25.0K Min. amount of faulty reference measurements to detect defective sensor 2.00[-]	Engine off time>= 360.00 min Engine off timeplausible Time after engine start<= 1400.0 s Depending on temperature slope Diff. actual vs previous IAT< 256.0K Diff. actual vs previous ECT@ cylinder headn.a. K Diff. actual vs previous ECT@ radiator outlet< 256.0K Diff. actual vs previous AAT< 256.0 K For time>= 1.0 s Depending on mean value condition Mean value of all temperature sensors @ cold start>= -256° C Number of valid sensors>= 2.00[-] Depending on block heater / solar radiation detection Time after engine start>= 0.5 s Vehicle speed>= 22 mph For time>= 20.0 s Diff. actual IAT @ manifold vs. min. IAT @ manifold< 5.0 K Diff. actual ECT @ cylinder head vs. min. ECT @ cylinder headn.a. K Diff. actual AAT vs. min. AAT< 4.0 K Diff. actual ECT @ radiator outlet vs. min. ECT @ radiator outlet< 1.1 K	0.1 s Once / DCY	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .
P0112 Intake Air Temperature Sensor 1 Circuit Low Bank 1	Intake Air Temperature Sensor Short To Ground	IAT sensor voltage < 0.10 V		0.5 s Continuous
P0113 Intake Air Temperature Sensor 1 Circuit High Bank 1	Intake Air Temperature Sensor open circuit	IAT sensor voltage > 4.50 V
P0116 Engine Coolant Temperature Sensor 1 Circuit Range/Performance	Engine Coolant Temperature Sensor @ Cylinder Head Rationality Check Inappropriately Low	Diff. min temperature of cross check sensors vs. ECT @ cylinder head @ engine start >= 25° C	Cross checks finished	1.0 s Once / DCY	2 DCY	-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor -G62-, CHECKING .
Engine Coolant Temperature Sensor @ Cylinder Head Rationality Check High		Difference between maximum and minimum temperature of ECT @ cylinder head < 1° C ECT @ cylinder head @ engine start> 40 - 80° C	ECT @ cylinder head> -256° C IAT @ throttle-48...143° C Depending on thermostat control: ECT @ cylinder headn.a.° C or ECT @ cylinder headn.a.° C Enginen.a. And Engine part load Or Engine full load Engine speed> 1300 rpm Vehicle speed>= 12 mph Engine load> 2.00 % For time>= 20.0 - 43.0 s Engineidle Vehicle speed< 3 mph Or Fuel cut offactive Or Engine stop for time>= 20.0 - 43.0 s Time after engine start> 100 s
Engine Coolant Temperature Sensor @ Cylinder Head Rationality Check Low		Difference between modelled and measured cylinder head temperature > 5° C	ECT @ cylinder head -128 - 127° C Time after engine start > 60.0 s	30 s Once / DCY
P0117 Engine Coolant Temperature Sensor 1 Circuit Low	Engine Coolant Temperature Sensor @ Cylinder Head Short To Ground	ECT sensor voltage @ cylinder head < 0.30 V		0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor -G62-, CHECKING .
P0118 Engine Coolant Temperature Sensor 1 Circuit High	Engine Coolant Temperature Sensor @ Cylinder Head Short To Battery / Open Circuit	ECT sensor voltage @ cylinder head > 4.90 V	Modeled IAT @ throttle >= -33° C Time after engine start> 60.0 s	0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor -G62-, CHECKING .
P0121 Throttle/Pedal Position Sensor/Switch "A" Circuit Range/Performance	Throttle Position Sensor 1 Rationality Check	Normalized difference between measured and modeled value of mass air flow from TPS 1 >= 1.00 [-] Or Relative mass air flow integral from TPS 1 > 60.0 [-]	Throttle adaptation not active	0.01 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
			Difference between TPS 1 and TPS 2 > 6.499° TPS			0.3 s Continuous
P0122 Throttle/Pedal Position Sensor/Switch "A" Circuit Low	Throttle Position Sensor 1 Short To Ground / open circuit	Throttle position sensor 1 voltage < 0.15 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P0123 Throttle/Pedal Position Sensor/Switch "A" Circuit High	Throttle Position Sensor 1 Short To Battery Voltage	Throttle position sensor 1 voltage > 4.85 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P0131 O2 Sensor Circuit Low Voltage Bank 1 Sensor 1	Oxygen Sensors Front Short To Ground	O2S sensor voltage < 0.15 V	Engine running	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P0132 O2 Sensor Circuit High Voltage Bank 1 Sensor 1	Oxygen Sensors Front Short To Battery Voltage	O2S sensor voltage > 5.20 - 5.35 V	Engine running	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P0133 O2 Sensor Circuit Slow Response Bank 1 Sensor 1	Oxygen Sensors Front Response Check	Dynamic Path: Lambda value vs. modeled lambda value >= 1.10 [-] Or Ratio of failed diagnostic cycle > n.a. [-]	General conditions: Injection mode change (DFI/MFI)not active ECT @ cylinder head>= -48° C Vehicle speed> 0 mph Integrated air mass after gear change> 0.0 g Air mass, lower range>= 0.00 mg/rev Air mass, upper range<= 1389.00 mg/rev Counter of integrated mass for fuel in oil< 255.00[-] And Time after engine start>= 0.0 s Or Integrated air mass per cylinder>= 0.00 kg Depending on canister and catalyst purge: Evap purge n.a. Or Evap purgen.a. Or Evap purgen.a. Canister load calculationn.a. Or Evap purgen.a. Canister loadn.a.[-] And Case 1: O2S frontn.a. Lambda stimulationn.a. Upper limit of lambda controller outputn.a. Lower limit of lambda controller outputn.a. Engine speedn.a.rpm Air massn.a. mg/rev MAFn.a. kg/h Catalyst purgen.a. And Depending on limited dynamic conditions: Integrated air massn.a.g Dynamic engine speedn.a.g Dynamic air massn.a.mg/rev Dynamic lambdan.a.% Or Dynamic engine speedn.a.rpm Diff. actual engine load vs. filtered engine load in limited dynamic conditions, lower rangen.a.kg/h Diff. actual engine load vs. filterd engine load in limited dynamic conditions, upper rangen.a.kg/h Dynamic torquen.a.[-] Case 2: lambda set value adjustment for conditioning and measuringactive	2.4 s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
Delay path: Lambda delay value vs. modeled lambda value > 1.10 [-]			General conditions: MAF >= 0.0 mg/rev MAF <= 1, 389.0 mg/rev Vehicle speed >= 0 mph Time after engine start >= 0.0 s Integrated mass for fuel in oil < 255.0 [-] Engine speed 1, 216 - 3, 008 RPM MAF (intake air rate) 20.0 - 150.0 kg/h Vehicle speed >= 3 mph Integrated MAF per cylinder >= 0.30 - 2.0 kg Depending on dynamic conditions: Dynamic engine speed < 288 RPM Dynamic torque < 80.0 Nm Dynamic MAF < 70.0 kg/h For time >= 0.6 s And depending on canister and catalyst purge: Evap purge n.a. Or Canister load calculation n.a Or Canister load <= n.a. [-]	13.2 s Once / DCY
P0135 O2 Sensor Heater Circuit Bank 1 Sensor 1	Oxygen Sensors Heater Front Functional Check	O2S ceramic temperature, < 630° C	O2S heater commanded on For time >= 10.0 s	20 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P0137 O2 Sensor Circuit Low Voltage Bank 1 Sensor 2	Oxygen Sensors Rear Short To Ground	O2S sensor voltage < 0.15 V	O2S heater active	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0138 O2 Sensor Circuit High Voltage Bank 1 Sensor 2	Oxygen Sensors Rear Short To Battery	O2S sensor voltage > 5.2 - 5.35 V	O2S heater active	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P013A O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2	Oxygen Sensors Rear Response Check	Gradient sensor voltage< 900.00mV/s	General conditions: Intrusive lambda ramp requestnot active Internal resistance O2S rear<= 700.00 Ohm Counter of integrated mass for fuel in oil< 255.00[-] Catalyst monitor lambda modulation requestactive Vehicle speed19 - 158 mph Barometric pressure>= 0.00kPa Catalyst overheating protectionnot active Turbine overheating protectionnot active O2S rearready O2S frontready ECT @ cylinder head> 60° C IAT @ manifold> -48° C Modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff.between dynamic and stationary catalyst temperature-150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear<= 900° C MAF per cylinder22.50 - 150.00 kg/h Air mass, lower range>= 0.00 mg/rev Air mass, upper range<= 650.00 - 1389.00mg/rev And Engine loadn.a.% Air mass setpointn.a.g/rev Accelerator pedal valuen.a. % For timen.a. s And Low dynamic conditions Dynamic engine speed< 50 rpm Dynamic air mass< 50.00 mg/rev Dynamic lambda controller output< 20.00 % And Integrated air mass after dynamic conditions are fulfilled> 20.0 g Time after a catalyst purge phase>= 1.0s O2S rear voltage @ diagnosis start>= 0.55V Integrated air mass>= 0.0 g Integrated heat energy>= 550 - 700 kJ Engine speed1, 088 - 3, 008 rpm Deviation of lambda controller output< 50.00 % Proportional part of secondary fuel control loopnot calibrated Coasting functionnot active O2S heater rearactive Lambda adaptationnot active Valve lift not active And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis< 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis< 0.25 [-] Depending on canister purge: Canister loadn.a.[-] Evap purge flown.a. Or Canister load calculationn.a. Evap purge flow n.a. Or Evap purge valven.a. Or Evap purge valven.a. Or Evap purge n.a. Or Depending on canister purge closing: Canister purge (conditions)n.a. Canister purge valve (closing time)n.a.s And Choice of: Evap purge valven.a. Or Evap purge valven.a. And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.40 - 1.80kg	0 FTP75: 50 s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P013B O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 2	Oxygen Sensors Rear Response Check	Gradient sensor voltage< 900.00mV/s	General conditions: Intrusive lambda ramp requestnot active Internal resistance O2S rear<= 700.00 Ohm Counter of integrated mass for fuel in oil< 255.00[-] Catalyst monitor lambda modulation requestactive Vehicle speed>= 19 mph Barometric pressure>= 0.00 kPa Catalyst overheating protectionnot active Turbine overheating protectionnot active O2S rearready O2S frontready ECT @ cylinder head> 60° C IAT @ manifold> -48° C Modeled catalyst temperature @ start of diagnosis 510 - 1, 775° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff. between dynamic and stationary catalyst temperature-150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear0 - 900° C MAF per cylinder22.50 - 150.00kg/h Air mass, lower range>= 0.00 mg/rev Air mass, upper range<= 650.00 - 1, 389.00mg/rev And Engine loadn.a.% Air mass setpointn.a.[g/rev] Accelerator pedal valuen.a.% For timen.a.s And Low dynamic conditions Dynamic engine speed< 50 rpm Dynamic air mass< 50, 000 mg/rev Dynamic lambda controller output< 20.00 % And Integrated air mass after dynamic conditions are fulfilled> 20.0 g Time after a catalyst purge phase>= 1.0s O2S rear voltage @ diagnosis start>= 0.55V Integrated air mass>= 0.0 g Integrated heat energy>= 550 - 700 kJ Engine speed1, 088 - 3, 008 rpm Deviation of lambda controller output< 50.00 % Proportional part of secondary fuel control loopnot calibrated % Coasting functionnot active O2S heater rearactive Lambda adaptationnot active Valve lift not active And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis< 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis< 0.25 [-] Depending on canister purge: Canister loadn.a.[-] Evap purge flown.a. Or Canister load calculationn.a. Evap purge flow n.a. Or Evap purge valven.a. Or Evap purge valven.a. Or Evap purge n.a. Or Depending on canister purge closing: Canister purge (conditions)n.a. Canister purge valve (closing time)n.a.s And Choice of: Evap purge valven.a. Or Evap purge valven.a. And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.45 - 1.80kg	0 FTP75: 50 s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P013E O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 2	Oxygen Sensors Rear Delayed Response Monitoring, Delay Measurement	Sensor signal delay time > 0.9 s	General conditions: Intrusive lambda ramp requestnot active Catalyst monitor lambda modulation requestactive Vehicle speed>= 19 mph Barometric pressure>= 0.00kPa Catalyst overheating protectionnot active Turbine overheating protectionnot active O2S rearready O2S frontready ECT @ cylinder head> 60° C IAT @ manifold> -48° C Modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff. between dynamic and stationary catalyst temperature-150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear<= 900° C MAF per cylinder22.50 - 150.00 kg/h Air mass, lower range>= 0.00 mg/rev Air mass, upper range<= 650.00 - 1, 389.00mg/rev And Engine loadn.a. % Air mass setpointn.a. g/rev Accelerator pedal valuen.a. % For timen.a.[s] And Low dynamic conditions Dynamic engine speed< 50 rpm Dynamic air mass< 50.00 mg/rev Dynamic lambda controller output< 20.00% And Integrated air mass after dynamic conditions are fulfilled> 20.0 g Time after a catalyst purge phase>= 1.0 s O2S rear voltage @ diagnosis start>= 0.55V Integrated air mass>= 0. [g Integrated heat energy>= 550.00 - 700.00 kJ Engine speed1, 088 - 3, 008 rpm Deviation of lambda controller output< 50.00% Proportional part of secondary fuel control loopnot calibrated[%] Coasting functionnot active O2S heater rearactive Lambda adaptationnot active Valve lift not active And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis< 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis< 0.25 [-] Depending on canister purge: Canister loadn.a.[-] Evap purge flown.a. Or Canister load calculationn.a. Evap purge flown.a. Or Evap purge valven.a. Or Evap purge valven.a. Or Evap purgen.a. Or Depending on canister purge closing: Canister purge (conditions)n.a. Canister purge valve (closing time)n.a.[s] And Choice of: Evap purge valven.a. Or Evap purge valven.a. And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.40 - 1.80kg	0 FTP75: 50 s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P013F O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 2	Oxygen Sensors Rear Delayed Response Monitoring, Delay Measurement	Sensor signal delay time > 1.5 s	General conditions: Intrusive lambda ramp requestnot active Catalyst monitor lambda modulation requestactive Vehicle speed>= 19 mph Barometric pressure>= 0.00 kPa Catalyst overheating protectionnot active Turbine overheating protectionnot active O2S rearready O2S frontready ECT @ cylinder head> 60° C IAT @ manifold> -48° C Modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff. between dynamic and stationary catalyst temperature-150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear<= 900° C MAF per cylinder22.50 - 150.00 kg/h Air mass, lower range>= 0.00 mg/rev Air mass, upper range<= 650.00 - 1, 389.00 mg/rev And Engine loadn.a.% Air mass setpointn.a. g/rev Accelerator pedal valuen.a. % For timen.a. s And Low dynamic conditions Dynamic engine speed< 50 rpm Dynamic air mass< 50.00 mg/rev Dynamic lambda controller output< 20.00 % And Integrated air mass after dynamic conditions are fulfilled> 20.0 g Time after a catalyst purge phase>= 1.0s O2S rear voltage @ diagnosis start>= 0.55V Integrated air mass>= 0.0 g Integrated heat energy>= 550.00 - 700.00 kJ Engine speed1, 088 - 3, 008 rpm Deviation of lambda controller output< 50.00 % Proportional part of secondary fuel control loopnot calibrated Coasting functionnot active O2S heater rearactive Lambda adaptationnot active Valve lift not active And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis< 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis< 0.25 [-] Depending on canister purge: Canister loadn.a.[-] Evap purge flown.a. Or Canister load calculationn.a. Evap purge flown.a. Or Evap purge valven.a. Or Evap purge valven.a. Or Evap purgen.a. Or Depending on canister purge closing: Canister purge (conditions)n.a. Canister purge valve (closing time)n.a. s And Choice of: Evap purge valven.a. Or Evap purge valven.a. And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.40 - 1.80kg	0 (FTP75: 50) s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0140 O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2	Oxygen Sensors Rear Open Circuit	Internal resistance of O2S (binary) > 25, 000.0 Ohm		2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0141 O2 Sensor Heater Circuit Bank 1 Sensor 2	Oxygen Sensors Heater Rear Out Of Range High	Internal resistance of O2S (binary) 700.0 - 25, 000.0 Ohm	O2S heatercommanded on For time >= 10.0 s	20 s Once / DCY	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0149 Fuel Timing Error	Injection Valves Supply Voltage Out Of Range Low	Boost voltage < 30.0 V	Engine running >= 0.3 s	3.6 s Continuous	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
					Boost voltage <= 50.0 V
Injection Valves Supply Voltage Out Of Range High		Boost voltage > 75.0 V
P0171 System Too Lean Bank 1	Fuel System, System Too Lean	Lambda controller output > 35.0 %	Lambda control closed loop Mass air flow > 60.0 mg/rev Engine speed > 576 RPM ECT @ cylinder head > 20° C IAT at intake manifold > -48° C AAT > -48° C And Evap purge valveclosed Or Canister load<= 1.20[-] Evap purge flowat max. value Or Depending on canister purge min: Lower limit of lambda controller outputn.a. Or Upper limit of lambda controller outputn.a. And Evap purge flowat min. value	60 s Continuous	2 DCY	-- Check the intake and vacuum hoses for leaks, Check the Positive Crankcase Ventilation, also make sure the oil dipstick is properly secured.-- Listen to and visually inspect the Exhaust system to insure there are no leaks.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0172 System Too Rich Bank 1	Fuel System, System Too Rich	Lambda controller output < -35.0 %	Lambda control closed loop Mass air flow > 60.0 mg/rev Engine speed > 576 RPM ECT @ cylinder head > 20° C IAT at intake manifold > -48° C AAT > -48° C Oil dilution not detected And Evap purge valveclosed Or Canister load<= 1.20[-] Evap purge flowat max. value Or Depending on canister purge min: Lower limit of lambda controller outputn.a. Or Upper limit of lambda controller outputn.a. And Evap purge flowat min. value	60 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING . -- Check the Evaporative Emission System for contamination. Refer to appropriate repair information.
P0190 Fuel Pressure Regulator 1 Control Circuit/Open	Fuel System Pressure Sensor High Pressure Side Short To Battery / Open Circuit	High fuel pressure sensor voltage > 4.80 V		2.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .-- Check the fuel pressure. Refer to appropriate repair information.
P0191 Fuel Rail Pressure Sensor Circuit Range/Performance Bank 1	Fuel Rail High Pressure Side Out Of Range High	Fuel pressure > 26, 500.18 kPa	Engine running Engine speed < 6, 816 RPM Time after engine start > 10.0 s	5.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .-- Check the fuel pressure. Refer to appropriate repair information.
P0192 Fuel Rail Pressure Sensor Circuit Low Bank 1	Fuel System Pressure Sensor High Pressure Side Short To Ground	High fuel pressure sensor voltage < 0.20 V		2.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .-- Check the fuel pressure. Refer to appropriate repair information.
P0201 Cylinder 1 Injector "A" Circuit	Injection Valves Electrical Error	Indeterminate fault pattern via power stage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector high side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector low side switch current driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector high side switch current driver stage internal value Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Electrical Error Open Circuit		Fault pattern for open circuit via power stage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
Injection Valves Electrical Error Short Circuit		Fault pattern for short circuit via power stage diagnosis detected Injector current rise time during peak phase < 0.064 ms
P0202 Cylinder 2 Injector "A" Circuit	Injection Valves Electrical Error	Indeterminate fault pattern via power stage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector high side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector low side switch current driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector high side switch current driver stage internal value Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Electrical Error Open Circuit		Fault pattern for open circuit via power stage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
Injection Valves Electrical Error Short Circuit		Fault pattern for short circuit via power stage diagnosis detected Injector current rise time during peak phase < 0.064 ms
P0203 Cylinder 3 Injector "A" Circuit	Injection Valves Electrical Error	Indeterminate fault pattern via power stage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector high side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector low side switch current driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector high side switch current driver stage internal value Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Electrical Error Open Circuit		Fault pattern for open circuit via power stage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
Injection Valves Electrical Error Short Circuit		Fault pattern for short circuit via power stage diagnosis detected Injector current rise time during peak phase < 0.064 ms
P0204 Cylinder 4 Injector "A" Circuit	Injection Valves Electrical Error	Indeterminate fault pattern via power stage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector high side switch current driver stage internal value Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current driver stage internal value Or Injector voltage < 2.0 V Injector low side switch current (hardware values) driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector low side switch current driver stage internal value Or Injector load resistance to ground and battery > 20.0 Ohm Injector high side switch current driver stage internal value Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Electrical Error Open Circuit		Fault pattern for open circuit via power stage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
Injection Valves Electrical Error Short Circuit		Fault pattern for short circuit via power stage diagnosis detected Injector current rise time during peak phase < 0.064 ms
P0221 Throttle/Pedal Position Sensor/Switch "B" Circuit Range/Performance	Throttle Position Sensor 2 Rationality Check	Normalized difference between measured and modeled value of mass air flow from TPS 2 >= 1.0 [-] Or Relative mass air flow integral from TPS 2> 60.00 -	Throttle adaptation (@ initial start or after detection of throttle exchange or checksum error) not active	0.01 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P0222 Throttle/Pedal Position Sensor/Switch "B" Circuit Low	Throttle Position Sensor 2 Short To Ground / Open Circuit	Throttle position sensor 2 voltage < 0.15 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P0223 Throttle/Pedal Position Sensor/Switch "B" Circuit High	Throttle Position Sensor 2 Short To Battery Voltage	Throttle position sensor 2 voltage > 4.85 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P0230 Fuel Pump Circuit	COM: Fuel Pump Control Module (FPCM) communication with FPCM	FP sensor: short to ground failure feedback>= 2.00[-]	Engineon	2.0 s Continuous	2 DCY
			FP sensor: open circuit failure feedback>= 2.00[-]			2.2 s Continuous
P0236 Turbocharger/Supercharger Boost Sensor "A" Circuit Range/Performance	Turbocharger Boost Pressure Sensor Rationality Check	Diff. barometric pressure vs. upstream throttle pressure >= 8.50 kPa Diff. upstream throttle pressure vs. intake manifold pressure >= 8.50 kPa Or Diff. barometric pressure vs. intake manifold pressure < 8.50 kPa	Case 1: Engine stop at start of DCY Enginestopped Vehicle speed< 1 mph Delay after engine stop>= 5.0 s Case 2: Engine stop during DCY Engine stopped Vehicle speed < 1 mph Delay after engine stop >= 5.0 s For time >= 10.0 s	3.0 s Once / DCY	2 DCY	-- Check the Charge Air Pressure Sensor -G31-. Refer to Charge Air Pressure Sensor -G31-, CHECKING .
P0237 Turbocharger/Supercharger Boost Sensor "A" Circuit Low	Turbocharger Boost pressure Sensor Short To Ground	Turbocharger boost pressure sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- Check the Charge Air Pressure Sensor -G31-. Refer to Charge Air Pressure Sensor -G31-, CHECKING .
P0238 Turbocharger/Supercharger Boost Sensor "A" Circuit High	Turbocharger Boost pressure Sensor Short To Battery Voltage	Turbocharger boost pressure sensor voltage > 4.80 V		0.5 s Continuous	2 DCY	-- Check the Charge Air Pressure Sensor -G31-. Refer to Charge Air Pressure Sensor -G31-, CHECKING .
P025A Fuel Pump Module "A" Control Circuit/Open	Fuel Pump Open Circuit	Signal voltage, lower range > 1.92 - 2.21 V And Signal voltage, upper range (hardware values) < 2.84 - 3.25 V	Commanded PWM 9.80 - 92.20 % Fuel pump commanded off	0.5 s Continuous	2 DCY	-- Check the Fuel Pump Control Module -J538- / Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .
P025C Fuel Pump Module "A" Control Circuit Low	Fuel Pump Short To Ground	Signal voltage (hardware values) < 1.92 - 2.21 V	Commanded PWM 9.80 - 92.20 % Fuel pump commanded off	3.0 s Continuous	2 DCY	-- Check the Fuel Pump Control Module -J538- / Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .
P025D Fuel Pump Module "A" Control Circuit High	Fuel Pump Short To Battery Voltage	Power stage temperature > 160 - 200° C Or Signal current (hardware values) driver stage internal value	Commanded PWM 9.80 - 92.20 % Fuel pump commanded on	0.5 s Continuous	2 DCY	-- Check the Fuel Pump Control Module -J538- / Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .
P0261 Cylinder 1 Injector "A" Circuit Low	Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Ground (High Side)		Injector driver voltage < 2 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 ms	720° CRK Continuous
Injection Valves Short To Ground (Low Side)		Injector driver voltage < 2 V And Injector driver high side switch current driver stage internal value And Injector driver low side switch current (hardware values) driver stage internal value
P0262 Cylinder 1 Injector "A" Circuit High	Injection Valves Short To Battery Plus	Fault pattern for short to Battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Battery Plus (High Side)		injector driver voltage > 2.0 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
Injection Valves Short To Battery Plus (Low Side)		Injector driver voltage > 2.0 V And Injector driver low side switch current (hardware values) driver stage internal value
P0264 Cylinder 2 Injector "A" Circuit Low	Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Ground (High Side)		Injector driver voltage < 2 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
Injection Valves Short To Ground (Low Side)		Injector driver voltage < 2 V And Injector driver high side switch current driver stage internal value And Injector driver low side switch current (hardware values) driver stage internal value
P0265 Cylinder 2 Injector "A" Circuit High	Injection Valves Short To Battery Plus	Fault pattern for short to Battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Battery Plus (High Side)	Injector driver voltage > 2.0 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
Injection Valves Short To Battery Plus (Low Side)	Injector driver voltage > 2.0 V And Injector driver low side switch current (hardware values) driver stage internal value
P0267 Cylinder 3 Injector "A" Circuit Low	Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Ground (High Side)	Injector driver voltage < 2 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
Injection Valves Short To Ground (Low Side)	Injector driver voltage < 2 V And Injector driver high side switch current driver stage internal value And Injector driver low side switch current (hardware values) driver stage internal value
P0268 Cylinder 3 Injector "A" Circuit High	Injection Valves Short To Battery Plus	Fault pattern for short to Battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Battery Plus (High Side)		Injector driver voltage > 2.0 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
Injection Valves Short To Battery Plus (Low Side)		Injector driver voltage > 2.0 V And Injector driver low side switch current (hardware values) driver stage internal value
P0270 Cylinder 4 Injector "A" Circuit Low	Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Ground (High Side)		Injector driver voltage < 2 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
Injection Valves Short To Ground (Low Side)		Injector driver voltage < 2 V And Injector driver high side switch current driver stage internal value And Injector driver low side switch current (hardware values) driver stage internal value
P0271 Cylinder 4 Injector "A" Circuit High	Injection Valves Short To Battery Plus	Fault pattern for short to Battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Injection Valves Short To Battery Plus (High Side)		Injector driver voltage > 2.0 V And Injector driver high side switch current (hardware values) driver stage internal value	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
Injection Valves Short To Battery Plus (Low Side)		Injector driver voltage > 2.0 V And Injector driver low side switch current (hardware values) driver stage internal value
P0300 Random/Multiple Cylinder Misfire Detected	Misfire Crankshaft Speed Fluctuation (Multiple)	Number of cylinders with emission threshold misfire within 4000 revolutions ≥ 2.00 [-] Or Number of cylinders with emission threshold misfire within 1000 revolutions ≥ 2.00 [-]	Emission threshold misfire detected	1000 rev Continuous	2 DCY	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check the fuel pressure. Refer to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
Number of cylinders with catalyst damaging misfire ≥ 2.00 [-]			Catalyst damaging misfire detected	200 rev Continuous	Immediate
P0301 Cylinder 1 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 5.20 - 20.83 %	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 for DCT: Time after engine start not calibrated Engine load > 1.99 - 37.99 % Depending on ECT @ cylinder head @ start ECT @ cylinder head @ start <= -48° C Then activation if ECT @ cylinder head>= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders< 2.00[-] And Dynamic manifold air pressurenot calibrated[kPa] Dynamic throttle positionnot calibrated And Dynamic of engine loadnot calibrated And Engine not calibrated Engine speednot calibrated[rpm] Dynamic of ignition angle @ idle speed not calibrated[°CRK] Or Dynamic of ignition anglenot calibrated[°CRK] And Rough roadnot detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check the fuel pressure. Refer to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1000 rev: Emission threshold misfire rate (MR) >= 2.05 %			1, 000 rev Continuous	2 DCY
			Emission threshold misfire within 4000 rev: Emission threshold misfire rate (MR) > 2.05 %			4 x 1, 000 rev Continuous
P0302 Cylinder 2 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 5.20 - 20.83 %	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 for DCT: Time after engine start not calibrated Engine load > 1.99 - 37.99 % Depending on ECT @ cylinder head @ start ECT @ cylinder head @ start <= -48° C Then activation if ECT @ cylinder head>= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders< 2.00[-] And Dynamic manifold air pressurenot calibrated[kPa] Dynamic throttle positionnot calibrated[°TPS/s] And Dynamic of engine loadnot calibrated[%] And Engine not calibrated Engine speednot calibrated[rpm] Dynamic of ignition angle @ idle speednot calibrated[°CRK] Or Dynamic of ignition anglenot calibrated[°CRK] And Rough roadnot detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check the fuel pressure. Refer to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1000 rev: Emission threshold misfire rate (MR) >= 2.05 %			1, 000 rev Continuous	2 DCY
			Emission threshold misfire within 4000 rev: Emission threshold misfire rate (MR) > 2.05 %			4 x 1, 000 rev Continuous
P0303 Cylinder 3 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 5.20 - 20.83 %	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 for DCT: Time after engine start not calibrated Engine load > 1.99 - 37.99 % Depending on ECT @ cylinder head @ start ECT @ cylinder head @ start <= -48° C Then activation if ECT @ cylinder head>= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders< 2.00[-] And Dynamic manifold air pressurenot calibrated[kPa] Dynamic throttle positionnot calibrated[°TPS/s] And Dynamic of engine loadnot calibrated[%] And Engine not calibrated Engine speednot calibrated[rpm] Dynamic of ignition angle @ idle speednot calibrated[°CRK] Or Dynamic of ignition anglenot calibrated[°CRK] And Rough roadnot detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check the fuel pressure. Refer to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1000 rev: Emission threshold misfire rate (MR) >= 2.05 %			1, 000 rev Continuous	2 DCY
			Emission threshold misfire within 4000 rev: Emission threshold misfire rate (MR) > 2.05 %			4 x 1, 000 rev Continuous
P0304 Cylinder 4 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 5.20 - 20.83 %	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 for DCT: Time after engine start not calibrated Engine load > 1.99 - 37.99 % Depending on ECT @ cylinder head @ start ECT @ cylinder head @ start <= -48° C Then activation if ECT @ cylinder head>= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders< 2.00[-] And Dynamic manifold air pressurenot calibrated[kPa] Dynamic throttle positionnot calibrated[°TPS/s] And Dynamic of engine loadnot calibrated[%] And Engine not calibrated Engine speednot calibrated[rpm] Dynamic of ignition angle @ idle speednot calibrated[°CRK] Or Dynamic of ignition anglenot calibrated[°CRK] And Rough roadnot detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check the fuel pressure. Refer to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1000 rev: Emission threshold misfire rate (MR) >= 2.05 %			1, 000 rev Continuous	2 DCY
			Emission threshold misfire within 4000 rev: Emission threshold misfire rate (MR) > 2.05 %			4 x 1, 000 rev Continuous
P0326 Knock/Combustion Vibration Sensor 1 Circuit Range/Performance Bank 1 or Single Sensor	Knock Sensor Rationality Check Low	Difference between knock sensor signal and average knock sensor signal < 0.00 - 0.12 V	ECT @ cylinder head > 59° C MAF > 229.00 mg/rev	4.3 s Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
P0327 Knock/Combustion Vibration Sensor 1 Circuit Low Bank 1 or Single Sensor	Knock Sensor Out Of Range	Sensor signal < 0.12 - 0.31 V	ECT @ cylinder head > 59° C MAF > 229.00 mg/rev Engine speed > 2, 016 RPM	4.0 s Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
P0335 Crankshaft Position Sensor "A" Circuit	Crankshaft Position Sensor Activity Check	Case 1: Counted exhaust camshaft signals without synchronization >= 17.00 [-] Or Counted intake camshaft signals without synchronization >= 17.00 [-] Case 2: Counted exhaust camshaft signals without synchronization n.a. [-] Or Counted intake camshaft signals without synchronization n.a. [-]	Signal edges @ selected camshaft signal detected Choice of: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Synchronization test incorrect Or Engine speed >= 380 RPM Or Engine running Engine stalling >= 5.0 s Or Backwards rotation not detected Or Engine speed >= 400 RPM Engine stop active	0.01 s Continuous	2 DCY	-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor -G40-, CHECKING .
P0336 Crankshaft Position Sensor "A" Circuit Range/Performance	RPM Sensor Out Of Range	Segment adaptation >= 0.70 %	Delay time>= 5, 760.00° CRK And Diff. actual air mass vs. previous air mass<= 20.01 - 39.99mg/rev Engine load<= 20.00 % Dynamic throttle position<= 269.50 - 398.40° TPS/s Rough roadnot detected Engine roughness signalnot valid Segments in fuel cut-off mode>= 32.00[-] Segment adaptationfinished Engine speed 2, 496 - 5, 024rpm Diff. between adapted value of cylinder 1 and cylinder 3< 0.70 % Diff. between adapted value of cylinder 2 and cylinder 4< 0.70 %	180.0° CRK Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Camshaft Position Sensor -G40-, CHECKING .
Counted teeth vs reference >= 1; <= 2 [-]			Engine running	3, 600.0° CRK Continuous
Crankshaft Position Sensor Rationality Check		Case 1: Engine speed > 3000 RPM Time between falling signal edges < 50 - 62.5 μs Case 2: Engine speed <= 3000 RPM Time between signal edges < 30 μs	Engine speed >= 400 RPM	4, 5720.0° CRK Continuous
Crankshaft Position Sensor Rationality Check		Crankshaft reference gap not detected	General conditions: Reference gap of reluctor wheel detected And Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Case 2: Engine speed >= 380 RPM Or Engine running And Engine stalling >= 5.0 s Or Case 3: Backwards rotation not detected Or Case 4: Engine speed >= 400 RPM Engine stopped	2, 160° CRK Continuous
Crankshaft Position Sensor Rationality Check		Counted teeth vs. reference >= 1; <= 2 [-]	General conditions: Engine speed> 320RPM And Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Case 2: Engine speed >= 380 RPM Or Engine running And Engine stalling >= 5.0 s Or Case 3: Backwards rotation not detected Or Case 4: Engine speed >= 400 RPM Engine stopped	1, 800° CRK Continuous
P0340 Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor	Camshaft Position Sensor Intake Signal Activity Check	No change on signal >= 3 [-]	Engine speed >= 400 RPM	4, 680.0° CRK Continuous	2 DCY	-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor -G40-, CHECKING .
P0341 Camshaft Position Sensor "A" Circuit Range/Performance Bank 1 or Single Sensor	Camshaft Position Sensor Intake Rationality Check	Ratio between measured segment time ratio and specified camshaft angle ratio > 2.75 [-] Or Ratio between measured segment time ratio and specified camshaft angle ratio < 0.36 [-] Or Offset between camshaft and crankshaft < -79.0° CRK Or Offset between camshaft and crankshaft > 15.0° CRK	Engine speed 400 - 8, 160 RPM	990.0° CRK Continuous	2 DCY	-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor -G40-, CHECKING .
			Camshaft Position Sensor Intake Signal Activity Check		Segment time value < 50 [μs]	1, 440.0° CRK Continuous
Camshaft Position Sensor Intake Angular Offset Check		Offset between camshaft and crankshaft < -79.00; OR > 15.0° CRK	Engine synchronization not validated Failure by exhaust camshaft sensor detected	450.0° CRK Once / DCY
P0365 Camshaft Position Sensor "B" Circuit Bank 1	Camshaft Position (CMP) Exhaust Sensor	No change on signal>= 3[-]	Engine speed >= 400rpm	1080.00° CRK Continuous	2 DCY	-- Check the Camshaft Position Sensor 3 -G300-. Refer to Camshaft Position Sensor 3 - G300-, CHECKING
P0366 Camshaft Position Sensor "B" Circuit Range/Performance Bank 1	Camshaft Position (CMP) Exhaust Sensor rationality check	Ratio between measured segment time ratio and specified camshaft angle ratio> 2.75[-] Or Ratio between measured segment time ratio and specified camshaft angle ratio< 0.36[-] Or Offset between camshaft and crankshaft< -24.00° CRK Or Offset between camshaft and crankshaft> 49.00° CRK	Engine speed400 - 8, 160rpm	990.00° CRK Continuous	2 DCY	-- Check the Camshaft Position Sensor 3 -G300-. Refer to Camshaft Position Sensor 3 - G300-, CHECKING
Camshaft Position (CMP) Exhaust Sensor signal activity check		Segment time value< 50[μs]	Engine speed400 - 8, 160 rpm	1440.00° CRK Continuous	2 DCY
Camshaft Position / Crankshaft Position (CMP/CKP) Exhaust Sensor out of range		Offset between camshaft and crankshaft< -24.00° CRK Or Offset between camshaft and crankshaft> 49.00° CRK	Engine synchronization via crankshaft and camshaftnot finished Or Engine synchronization via crankshaft and camshaftlost	450.00° CRK Once / DCY"	2 DCY
P039B Cylinder 1 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Torque limitation factor < 0.90 [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load n.a. % Mass air flow > 501.00 - 599.00 mg/rev Dynamic engine speed not active Delay time 0.00 sec	900.0° CRK Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
					Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold <= n.a. [-] Or Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-]
P03A5 Cylinder 2 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Torque limitation factor < 0.90 [-]	Engine running ECT @ cylinder head > 60° C Engine speed 1, 216 - 6, 400 RPM Engine load n.a. % Mass air flow > 403.00 - 447.00 mg/rev Dynamic engine speed not active	900.0° CRK Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
					Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold <= n.a. [-] Or Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-]
P03AF Cylinder 3 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Torque limitation factor < 0.90 [-]	Engine running ECT @ cylinder head > 60° C Engine speed 1, 216 - 6, 400 RPM Engine load n.a. % Mass air flow > 403.00 - 447.00 mg/rev Dynamic engine speed not active	900.0° CRK Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
					Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold <= n.a. [-] Or Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-]
P03B9 Cylinder 4 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.00 [-] Ratio between knock sensor and knock threshold in main knock window > 2.00 - 3.00 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Torque limitation factor < 0.90 [-]	Engine running ECT @ cylinder head > 60° C Engine speed 1, 216 - 6, 400 RPM Engine load n.a. % Mass air flow > 403.00 - 447.00 mg/rev Dynamic engine speed not active	900.0° CRK Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
					Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold <= n.a. [-] Or Ratio between normalized engine roughness and misfire detection threshold <= n.a. [-]
P0410 AIR System "A"	Secondary Air System Functional Check	Diff. pressure value after secondary air injection vs. pressure value before secondary air activation > 5.0 kPa	General: Secondary air pump ready Catalyst heating active Secondary air injection finished MAF <= 140.0 kg/h ECT @ cylinder head >= -10; < 115° C IAT @ manifold >= -10; < 100° C Modeled catalyst temperature < 900° C Relative barometric pressure > 0.73 [-] Diff. barometric pressure vs. manifold pressure > n.a. kPa	0.1 s Once / DCY	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .-- Check the Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-. Refer to Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-, CHECKING .
P0413 AIR System Switching Valve "A" Circuit Open	Secondary Air Valve Open Circuit	Output voltage, lower range >= 1.92 - 2.21 V Output voltage, upper range (hardware values) <= 2.85 - 3.25 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .
P0414 AIR System Switching Valve "A" Circuit Shorted	Secondary Air Valve Short To Ground	Output voltage (hardware values) < 1.92 - 2.21 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .
Secondary Air Valve Short To Battery Plus		Actuator temperature > 160 - 200° C Or Output current (hardware values) driver stage internal value	Engine running Actuator commanded on
P0418 AIR System Control "A" Circuit	Secondary Air Injection Pump Relay Open Circuit	Output voltage, lower range 1.92 - 2.21 V Output voltage, upper range (hardware values) <= 2.85 - 3.25 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-. Refer to Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-, CHECKING .
P0420 Catalyst System Efficiency Below Threshold Bank 1	NMOG / NMHC Conversion Capability	Catalyst efficiency > 1.00 [-]	Catalyst monitor lambda modulation request active General conditions: Vehicle speed >= 19 mph BARO >= 0.00 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rear ready O2S front ready ECT @ cylinder head > 60° C IAT@ manifold > -48° C modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis 470 - 830° C Difference between dynamic and stationary catalyst temperature -150 - 150° C Integrated MAF, catalyst temp. conditions fulfilled >= 0.0 g Modeled EGT @ O2S rear <= 900° C MAF per cylinder 22.50 - 150.00 kg/h Air mass, lower range >= 0.00 mg/rev Air mass, upper range <= 650.00 - 1, 389.00 mg/rev And Engine loadn.a.[%] Air mass setpointn.a.[g/rev] Accelerator pedal valuen.a.[%] For timen.a.[s] And Low dynamic conditions Dynamic engine speed< 50 rpm Dynamic air mass< 50.00 mg/rev Dynamic lambda controller output< 20.00 % And Integrated air mass after dynamic conditions are fulfilled> 20.0 g Time after a catalyst purge phase>= 1.0s O2S rear voltage @ diagnosis start>= 0.55V Integrated air mass>= 0.0 g Integrated heat energy>= 550.00 - 700.00 kJ Engine speed1, 088 - 3, 008rpm Deviation of lambda controller output< 50.00 % Proportional part of secondary fuel control loopnot calibrated % Coasting functionnot active O2S heater rearactive Lambda adaptationnot active Valve lift not active And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis< 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis< 0.25 [-] Depending on canister purge: Canister loadn.a.[-] Evap purge flown.a. Or Canister load calculationn.a. Evap purge flow n.a. Or Evap purge valven.a. Or Evap purge valven.a. Or Evap purgen.a. Or Depending on canister purge closing: Canister purge (conditions)n.a. Canister purge valve (closing time)n.a.[s] And Choice of: Evap purge valven.a. Or Evap purge valven.a. And Modeled air mass integral> 50.0g Integrated air mass per cylinder>= 1.45 - 1.70kg Internal resistance O2S rear<= 700.00 Ohm	60.0 - 70.0 s Once / DCY	1 DCY	-- Check the Three Way Catalytic Converter. Refer to appropriate repair information.-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P0441 EVAP System Incorrect Purge Flow	EVAP Purge ValveFunctional Check: Stuck Close	Ratio actual intake manifold pressure and modeled set point intake manifold pressure < 0.10[-]	ECT @ cylinder head > 60° C Barometric pressure > 73.0 kPa AAT > 5° C AAT @ start< 5° C Diff. barometric pressure vs. filtered intake manifold pressuren.a. Diff. barometric pressure vs. filtered intake manifold pressure> 28.00 kPa Ratio MAF @ intake manifold and MAF max. > 0.07 - 0.10[-] Engine speed1, 180 - 2, 800 RPM Vehicle speed >= 11mph Diff. engine speed vs. filtered engine speed< 90 RPM Diff. ratio MAF @ intake manifold and MAF max vs. ratio filtered MAF @ intake manifold and MAF max< 0.15 [-] Diff. modeled intake manifold pressure vs. filtered modeled intake manifold pressure < 1.50 - 2.50 kPa And Integrated MAF since engine start >= 0.0 - 5, 000.0g Lambda control active Lambda control value -30.00 - 30.00 % O2S front 0.90 - 1.10 [-] or Fuel cut off not calibrated Case 1: Integrated MAF @ canister purge per driving cycle>= n.a. g Case 2: ratio MAF @ canister purge and MAF per cylinder>= 0.00[-] Or Canister purge sampling rate>= 20.00 % And Integrated air mass @ canister purge valve>= 31.9g Depending on AAT: AAT>= 30° C Canister load <= 0.20 [-] Or AAT>= 50; < 30° C Canister load <= 0.20 [-] Or AAT < 50° C Canister load <= 0.20 [-]	8.5 s Once / DCY	2 DCY	-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 -N80-, CHECKING .
P0444 EVAP System Purge Control Valve "A" Circuit Open	EVAP Purge Valve Open Circuit	Output voltage, lower range >= 1.92 - 2.21 V Output voltage, upper range (hardware values) <= 2.85 - 3.25 V	Engine start not active Engine running Evap purge valve opening signal (PWM) > 3.13; <= 98.83 % Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 -N80-, CHECKING .
P0445 EVAP System Purge Control Valve "A" Circuit Shorted	EVAP Purge Valve Short To Ground	Output voltage (hardware values) 1.92 - 2.21 V	Engine start not active Engine running Evap purge valve opening signal (PWM) <= 98.83 % Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 -N80-, CHECKING .
EVAP Purge Valve Short To Battery Plus		Actuator temperature 160 - 200° C Or Output current (hardware values) driver stage internal value	Engine start not active Engine running Evap purge valve opening signal (PWM) >= 3.13 % Actuator commanded on
P0450 EVAP System Pressure Sensor/Switch Circuit	NVLD Switch Open Circuit	Signal voltage 0.39 - 0.55 V	Case 1: Engine running Case 2: Ignition off NVLD (EVAP-System) diagnostic mode active	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P0451 EVAP System Pressure Sensor/Switch Circuit Range/Performance	NVLD Switch Functional Check Stuck Close	Natural vacuum leak detection (NVLD) switch position closed	Ignition off Fuel level < 85.10 % Fuel temperature increase >= 5 K For time >= 1.0 h AAT >= 4° C Barometric pressure >= 73.0 kPa Time since ignition off > 20; < 1, 440 min	0.1 s Once / DCY	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P0452 EVAP System Pressure Sensor/Switch Circuit Low	NVLD Switch Short To Ground	Signal voltage < 0.24 V	Case 1: Engine running Case 2: Ignition off NVLD (EVAP-System) diagnostic mode active	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P0453 EVAP System Pressure Sensor/Switch Circuit High	NVLD Switch Short To Battery Plus	Signal voltage > 3.0 V	Case 1: Engine running Case 2: Ignition off NVLD (EVAP-System) diagnostic mode active	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P0456 EVAP System Leak Detected (Very Small Leak)	EVAP System Small Leak Functional Check	Natural vacuum leak detection (NVLD) switch position = open	Ignition off Fuel level < 85.10 % Fuel temperature drop >= 6 K For time > 1 h AAT >= 4° C Barometric pressure > 73.00 kPa Diff. barometric pressure @ stop and barometric pressure @ start < 0.65 kPa Time since ignition off > 90 [min] ; < 600 min	0.1 s Once / DCY	2 DCY	-- Check the EVAP System visually for any leaking hoses or damage to components.-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 -N80-, CHECKING .-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P0461 Fuel Level Sensor "A" Circuit Range/Performance	Fuel Level Plausibility Check	Diff. fuel consumption And Fuel level changes < -25.0; > 12.0 [-]	General: Refueling or defuelingnot detected And Case 1: For tank full fuel level > 96.09 % Fuel consumption since last refueling or last plausibility check > 44.0 [-] Case 2: For tank not full fuel level <= 96.09 % Fuel consumption since last refueling or last plausibility check > 15.0 l	1.0 s Multiple	2 DCY	Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P0462 Fuel Level Sensor "A" Circuit Low	CAN: Fuel Level Sensor 1 CAN Communication With Instrument Cluster Module	Instrument cluster module signal: short to ground failure		0.5 s Continuous	2 DCY	Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
					Instrument cluster module signal: signal range check failure
P0463 Fuel Level Sensor "A" Circuit High	CAN: Fuel Level Sensor 1 CAN Communication With Instrument Cluster Module	Instrument cluster module signal: short to battery / open circuit failure		0.5 s Continuous	2 DCY	Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P0491 AIR System Insufficient Flow Bank 1	Secondary Air System Functional Check	Case 1: Blockage: ratio relative measured secondary air pressure and modelled secondary air pressure [tube blocked] < 0.70 [-] Or Leakage: ratio relative measured secondary air pressure and modelled secondary air pressure [leak diagnosis] < 0.65 [-] Case 2: Diff. expected integrated secondary air pressure pulsations and actual integrated secondary air pressure pulsations n.a. kPa Case 3: Blockage: ratio relative measured secondary air pressure and modelled secondary air pressure [tube blocked] < 0.40 [-] Or Leakage: ratio relative measured secondary air pressure and modelled secondary air pressure [leak diagnosis] < 0.15 [-]	General: Secondary air pump active Catalyst heating active Secondary air injection active MAF <= 140.0 kg/h ECT @ cylinder head >= -10; < 115° C IAT @ manifold >= -10; < 100° C Modelled catalyst temperature < 900° C Relative barometric pressure > 0.73 [-] Diff. barometric pressure vs. manifold pressure > n.a. kPa	0.1 s Once / DCY	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .-- Check the Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-. Refer to Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-, CHECKING .
P0501 Vehicle Speed Sensor "A" Circuit Range/Performance	CAN: Vehicle Speed Sensor CAN Communication With Vehicle Speed Sensor	Speed sensor fault value: Out of range high failure		0.5 s Continuous	2 DCY	-- Check the Vehicle Speed Signal. Refer to VEHICLE SPEED SIGNAL, CHECKING
					Speed sensor fault value: Out of range low failure
					Speed sensor fault value: Rationality check high failure
					Speed sensor fault value: Rationality check low failure
P0502 Vehicle Speed Sensor "A" Circuit Low	Vehicle Speed Sensor (VSS) short to ground	Diagnostic signal from output driver failure		0.5 s Continuous	2 DCY	-- Check the Vehicle Speed Signal. Refer to VEHICLE SPEED SIGNAL, CHECKING
				Vehicle Speed Sensor (VSS) open circuit
				Vehicle Speed Sensor (VSS) short to battery plus
P0506 Idle Control System RPM - Lower Than Expected	Idle Speed Control (ISC) function monitoring: engine speed deviation	Diff. actual engine speed vs. engine speed setpoint < -100 RPM Integrated I-part of idle speed controller n.a.	General conditions: Vehicle speed=0 mph Accelerator pedalreleased by driver Throttle actuatorcommanded on Evap purge flow< 4.00 kg/h Enginerunning Time after engine start> 0.0s Clutch switchn.a. Barometric pressure> 70.00kPa Catalyst heatingnot active ECT @ cylinder head> -48° C And Setpoint changen.a.rpm For timen.a. s And Additional after dynamic conditions fulfilled: Gear switchnot active (A/T only) Accelerator pedalreleased by driver Vehicle speed 0mph Engine load< 31.25% (M/T only) For time>= 0.0 s	12.0 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P0507 Idle Control System RPM - Higher Than Expected	Idle Speed Control (ISC) function monitoring: engine speed deviation	Diff. actual engine speed vs. engine speed setpoint > 90 RPM Integrated I-part of idle speed controller n.a.	General conditions: Vehicle speed=0 mph Accelerator pedalreleased by driver Throttle actuatorcommanded on Evap purge flow< 4.00 kg/h Enginerunning Time after engine start> 0.0 s Clutch switchn.a. Barometric pressure> 70.00kPa Catalyst heatingnot active ECT @ cylinder head> -48° C And Setpoint changen.a.rpm For timen.a. s And Additional after dynamic conditions fulfilled: Gear switchnot active (A/T only) Accelerator pedalreleased by driver Vehicle speed0 mph (M/T only) For time>= 0.0 s	12 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P050A Cold Start Idle Control System Performance	Cold Idle Controller Function Monitoring: engine speed deviation	Positive engine speed vs. engine speed set point > 90 RPM Integrated I-part of idle speed controller n.a.	General conditions: Vehicle speed=0 mph Accelerator pedalreleased by driver Throttle actuatorcommanded on Evap purge flow< 4.00 kg/h Enginerunning Time after engine start> 0.0 s Clutch switchn.a. Barometric pressure> 70.00kPa Catalyst heatingactive ECT @ cylinder head> -10° C And Setpoint changen.a.rpm For timen.a.s And Additional after dynamic conditions fulfilled: Gear switchnot active (A/T only) Accelerator pedalreleased by driver Vehicle speed0mph For time>= 0.0s	12 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
Cold Idle Controller Function Monitoring: engine speed deviation		Negative engine speed deviation from set point > 100 RPM Integrated I-part of idle speed controller n.a.	General conditions: Vehicle speed=0 mph Accelerator pedalreleased by driver Throttle actuatorcommanded on Evap purge flow< 4.00kg/h Enginerunning Time after engine start> 0.0s Clutch switchn.a. Barometric pressure> 70.00kPa Catalyst heatingactive ECT @ cylinder head> -10° C And Setpoint changen.a. rpm For timen.a. s And Additional after dynamic conditions fulfilled: Gear switchnot active (A/T only) Accelerator pedalreleased by driver Vehicle speed0mph Engine load< 31.25% (M/T only) For time>= 0.0 s
P050B Cold Start Ignition Timing Performance	Ignition Control Ignition Timing Monitor	Ratio between ignition angle efficiency integral and time at idle speed > 0.20 [-]	Engine idle speed time @ idle speed > 5.0 s Ignition angle setpoint <= 0.85 [-] Modeled pressure quotient <= 1.0 [-] Vehicle speed = 0 mph And Diff. air mass set point vs. filtered air mass set point for load dynamic detection < 99, 999.00 mg/rev For time >= 0.0 s And Diff. engine speed vs. filtered engine speed for engine speed dynamic detection < 8, 160 RPM For time >= 0.0 s	0.1 s Once / DCY	2 DCY	-- Check for any Engine Speed sensor or Ignition Coil faults and diagnose them first.-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor -G28-, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .-- If NO other codes are set, check the ECM. Refer to appropriate repair information.-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
P052A Cold Start "A" Camshaft Position Timing Over-Advanced Bank 1	Cold Start Monitoring Variable Valve Timing (VVT) Intake Actuator rationality check	Camshaft position deviation> 9.00° CRK	Modeled oil temperature-40 - 160° C Engine speed608 - 6, 016rpm Camshaft positionn.a. Camshaft position adjustmentactive Catalyst heatingactive Camshaft position deviation integrator (actual vs. setpoint position)>= 8.00° CRK's	0 (FTP75: 45) [s] once / DCY	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 -N205-, CHECKING
P053F Cold Start Fuel Pressure Performance Bank 2	Fuel System Out Of Range High	Deviation between reference and actual fuel pressure < -2, 999.90 kPa For time >= 3.0 s	General: Engine speed> 512 rpm Time after engine start> 10.0 s And Fuel mass setpoint lower range> 5.00 mg/rev for time>= 10.0 s Fuel mass setpoint upper range<= 187.17 - 229.23 mg/rev Fuel mass setpoint gradient-1389.00 - 1389.00 mg/rev For time>= 5.0s And Additional for catalyst heating: Catalyst heatingactive ECT @ cylinder head> -48° C Fuel mass setpoint lower range>= 5.00 mg/rev For time>= 5.1 s	4.5 s Once / DCY	2 DCY	-- Check the fuel pressure. Refer to appropriate repair information.-- Check the Fuel Pump Control Module -J538- / Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING Fuel Pressure Regulator Valve -N276-, CHECKING .-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .
Fuel System Out Of Range Low		Deviation between reference and actual fuel pressure > 2, 999.90 kPa For time >= 3.0 s
P054A Cold Start "B" Camshaft Position Timing Over-Advanced Bank 1	Cold Start Monitoring Variable Valve Timing (VVT) Exhaust Actuator rationality check	Camshaft position deviation> 9.00° CRK	Modeled oil temperature-40...160° C Engine speed 608 - 6, 016 rpm Camshaft positionn.a. Camshaft position adjustmentactive Catalyst heatingactive Camshaft position deviation integrator (actual vs. setpoint position)>= 8.00° CRK's	0 (FTP75: 45) s Once / DCY	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 -N318-, CHECKING
P064A Fuel Pump Control Module	COM: Fuel Pump Control Module (FPCM) communication with FPCM	FP signal: ROM / RAM failure feedback>= 2.00[-]	Engineon	1.2 s Continuous	2 DCY	-- Check the Fuel Pump Control Module -J538- / Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .
			FP signal: power amplifier failure feedback>= 2.00 [-]			1.4 s Continuous
P0601 Internal Control Module Memory Checksum Error	ECM: Checksum Verification	Calibration checksum incorrect		1.0 s Continuous	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
					Software checksum incorrect
P0603 Internal Control Module Keep Alive Memory (KAM) Error	Injection Valves Supply Voltage Internal Hardware Check	Hardware vs. software version check during initialization failure		4.9 s Once / DCY	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
					Calibration during initialization failure
					Hardware during initialization failure
					Time reference from micro controller during initialization failure
			Time reference from micro controller during initialization missing			2, 880.0° CRK Continuous
			Communication between micro controller and SDI-Driver power stage failure			2880.0° CRK Continuous
			Communication between micro controller and SDI-Driver power stage failure			360.0° CRK Once / DCY
			ECM: Communication Check		Device 1: SPI communication with ATIC failure	2.0 s Continuous
					Device 2: SPI communication with ATIC failure
					SPI communication with ATIC failure
P0606 Control Module Processor	Barometric Pressure Sensor Rationality Check By Engine Off*	Diff. barometric pressure vs. upstream throttle pressure >= 8.50 kPa Or Diff. barometric pressure vs. intake manifold pressure >= 8.50 kPa	Case 1: Engine stop during DCY Engine stopped Vehicle speed < 1 mph Case 2: Engine stop at start of DCY Engine stopped Vehicle speed < 1 mph Delay after engine stop >= 5.0 s For time >= 10.0 s	3.0 s Multiple	2 DCY	-- Using scan tool, monitor the Barometric Pressure Sensor, located within the Engine Control Module -J623-.-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
Barometric Pressure Sensor Rationality Check During ECM Keep Alive-Time:*		Case 1: Diff. barometric pressure vs. intake manifold pressure>= 8.50 kPa And Diff. barometric pressure vs. upstream throttle pressure>= 8.50 kPa Case 2: Diff. intake manifold pressure vs. intake manifold pressure @ idle or low part loadn.a.kPa Diff. barometric pressure vs. intake manifold pressuren.a. kPa Diff. barometric pressure vs. upstream throttle pressuren.a. kPa Case 3: Diff. upstream throttle pressure @ full or high part load vs. upstream throttle pressuren.a. kPa Diff. barometric pressure vs. intake manifold pressuren.a. kPa Diff. barometric pressure vs. upstream throttle pressuren.a.kPa Diff. upstream throttle pressure vs. intake manifold pressuren.a.kPa	Engine stopped Vehicle speed < 1 mph Ignition off Delay time in ECM keep alive-time > 10.0 s Delay after engine stop >= 5.0 s Barometric pressure sensor voltage 0.20 - 4.80 V intake manifold pressure sensor voltage 0.20 - 4.80 V Turbocharger boost pressure sensor voltage 0.20 - 4.80 V	3.0 s Once / DCY
Barometric Pressure Sensor Out Of Range High*		Measured barometric pressure > 115.0 kPa		5.0 s Continuous
Barometric Pressure Sensor Out Of Range Low*		Measured barometric pressure < 45.0 kPa
Knock Control Functional Check*		Knock control failure	Engine running	6.4 s Continuous
ECM: EEPROM Check*		EEPROM information failure Decryption of NVMCrypt failed Finished NVMCrypt integrity error Communication between sample software and production hardware error RAM error detected Monitoring module check failed		1.0 s Once / DCY
ECM: Communication Check*		SPI communication with ATIC failure	Time after ignition on >= 1.0 s	1.0 s Continuous
ECM: A/D Converter Function Monitoring: A/D Converter*		Diff. A/D-channel 1 vs. A/D-channel 2 > 0.30 V		0.5 s Continuous
ECM: Electronic Throttle Control Module Function Monitoring: Torque*		Monitoring of difference between actual and set point torque value engine torque overflow > 45.00 - 350.00 Nm	Throttle actuator commanded on	0.5 s Continuous
			Monitoring of torque difference integration integrated engine torque > 655.35 Nm			0.01 s Continuous
ECM: Electronic Throttle Control Module Function Monitoring: Engine Speed Limitation*		Engine speed > 1, 760 RPM	Engine speed limitation active Injection active	0.5 s Continuous
ECM: Electronic Throttle Control Module Function Monitoring: A/D Converter*		Internal check failed		0.5 s Continuous
CAN: Controller controller RAM check *		RAM errormemory checksum error	Initialization phaseactive Ignitionon	0.2 s Once / DCY
P0607 Control Module Performance	Barometric Pressure Sensor Short To Ground	Barometric pressure sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- Using scan tool, monitor the Barometric Pressure Sensor, located within the Engine Control Module -J623-.-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
Barometric Pressure Sensor Short To Battery Plus		Barometric pressure sensor voltage > 4.80 V
P0638 Throttle Actuator Control Range/Performance Bank 1	Throttle Actuator Basic Settings Adaptation Value Monitoring	Battery voltage <= 9.04 V	Throttle adaptation (@ initial start or after detection of throttle exchange or checksum error) active	0.01 s Once Per Lifetime	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
			Accelerator pedal value > 99.90 % Or Engine speed > 64 RPM Or Vehicle speed > 1 mph Or Modeled IAT @ throttle < 5° C Or ECT @ cylinder head < 5° C Or ECT @ cylinder head > 110° C			0.01 s Once Per Lifetime
Actual TPS 1 or 2 voltage - voltage ref. point > 0.07 V			Throttle adaptation demanded Accelerator pedal value < 99.90 % Engine speed < 64 RPM Vehicle speed < 1 mph Modeled IAT @ throttle > 5° C ECT @ cylinder head 5 - 110° C	0.01 s Once / DCY
			Actual TPS - ref. point > 0.503° TPS			0.01 s Once / DCY
			Throttle Actuator Basic Settings Monitoring Of Position		Actual TPS - ref. point > 0.503° TPS	0.01 s Once Per Lifetime
					Throttle position sensor 1 voltage < 0.40 V Or Throttle position sensor 2 voltage > 4.60 V Or Throttle position sensor 1 voltage > 0.80 V Or Throttle position sensor 2 voltage < 4.20 V
					Actual TPS 1 or 2 voltage - voltage ref. point > 0.07 V
					Actual TPS 1 or 2 voltage - voltage ref. point > 0.25 V
					Actual TPS - ref. point > 0.503° TPS
					Actual TPS 1 or 2 voltage - voltage ref. point > 0.07 V
P0642 Sensor Reference Voltage "A" Circuit Low	ECM: 5V Supply Voltage Out Of Range Low	Analog output 1 supply voltage < 4.62 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0643 Sensor Reference Voltage "A" Circuit High	ECM: 5V Supply Voltage Out Of Range High	Analog output 1 supply voltage > 5.43 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0652 Sensor Reference Voltage "B" Circuit Low	ECM: 5V Supply Voltage Out Of Range Low	Analog output 2 supply voltage < 4.62 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0653 Sensor Reference Voltage "B" Circuit High	ECM: 5V Supply Voltage Out Of Range High	Analog output 2 supply voltage > 5.43 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0657 Actuator Supply Voltage "A" Circuit/Open	Supply Voltage Relay Engine Components Open Circuit	Output voltage, lower range >= 1.90 - 2.30 V Output voltage, upper range (hardware values) <= 2.80 - 3.20V	Relay commanded off	1.0 s Continuous	2 DCY	-- Check the Engine Component Power Supply Relay -J757-. Refer to Engine Component Power Supply Relay -J757-, CHECKING .
P0658 Actuator Supply Voltage "A" Circuit Low	Supply Voltage Relay Engine Components Short To Ground	Output voltage (hardware values) < 1.90 - 2.30 V	Relay commanded off	0.1 s Continuous	2 DCY	-- Check the Engine Component Power Supply Relay -J757-. Refer to Engine Component Power Supply Relay -J757-, CHECKING .
P0659 Actuator Supply Voltage "A" Circuit High	Supply Voltage Relay Engine Components Short To Battery Voltage	Output current driver stage internal value Or Actuator temperature (hardware values) > 175 - 195° C	Relay commanded on	0.1 s Continuous	2 DCY	-- Check the Engine Component Power Supply Relay -J757-. Refer to Engine Component Power Supply Relay -J757-, CHECKING .
P0686 ECM/PCM Power Relay Control Circuit Low	Main Relay Rationality Check During Engine Off	Sensed circuit voltage > 6.00V	Main relaycommanded on For time>= 0.3 s	0.1 s Continuous	2 DCY	-- Check the Motronic Engine Control Module Power Supply Relay -J271-. Refer to Motronic Engine Control Module Power Supply Relay -J271-, CHECKING .
P0687 ECM/PCM Power Relay Control Circuit High	Main Relay Rationality Check During Engine Running	Sensed circuit voltage < 5.00 V	Main relay commanded on For time>= 0.1 s	0.1 s Continuous	2 DCY	-- Check the Motronic Engine Control Module Power Supply Relay -J271-. Refer to Motronic Engine Control Module Power Supply Relay -J271-, CHECKING .
Main Relay Short To Battery Plus		Main relay driver temperature > 175 - 195° C Or Main relay output current (hardware values) driver stage internal value	Main relay commanded on For time>= 0.4 s	0.2 s Continuous
P0698 Sensor Reference Voltage "C" Circuit Low	ECM: 5V Supply Voltage Out Of Range Low	Analog output 3 supply voltage < 4.62 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0699 Sensor Reference Voltage "C" Circuit High	ECM: 5V Supply Voltage Out Of Range High	Analog output 3 supply voltage > 5.43 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P11A1 Cam Shift Actuator "A" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 1 -F366-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11A2 Cam Shift Actuator "A" Cylinder 1 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 1 -F366-. Refer to Cam Adjustment Actuators --, CHECKING
P11A3 Cam Shift Actuator "B" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 2 -F367-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11A4 Cam Shift Actuator "B" Cylinder 1 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 2 -F367-. Refer to Cam Adjustment Actuators --, CHECKING
P11A5 Cam Shift Actuator "A" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 3 -F368-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11A6 Cam Shift Actuator "A" Cylinder 2 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 3 -F368-. Refer to Cam Adjustment Actuators --, CHECKING
P11A7 Cam Shift Actuator "B" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 4 -F369-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11A8 Cam Shift Actuator "B" Cylinder 2 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 4 -F369-. Refer to Cam Adjustment Actuators --, CHECKING
P11A9 Cam Shift Actuator "A" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 5 -F370-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11AA Cam Shift Actuator "A" Cylinder 3 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 5 -F370-. Refer to Cam Adjustment Actuators --, CHECKING
P11AB Cam Shift Actuator "B" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 6 -F371-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11AC Cam Shift Actuator "B" Cylinder 3 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 6 -F371-. Refer to Cam Adjustment Actuators --, CHECKING
P11AD Cam Shift Actuator "A" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 7 -F372-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11AE Cam Shift Actuator "A" Cylinder 4 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 7 -F372-. Refer to Cam Adjustment Actuators --, CHECKING
P11AF Cam Shift Actuator "B" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) short to ground	Output voltage< 1.92 - 2.21V (hardware values)	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 8 -F373-. Refer to Cam Adjustment Actuators --, CHECKING
			Variable Valve Lift (VVL) open circuit		Output voltage, lower range< 1.92 - 2.21V Output voltage, upper range> 2.85 - 3.25V	2 DCY
P11B0 Cam Shift Actuator "B" Cylinder 4 Range/Performance	Variable Valve Lift (VVL) rationality check low	Actuator feedback signal voltage permanently low[-]	Modeled oil temperature< 20° C	6.0 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 8 -F373-. Refer to Cam Adjustment Actuators --, CHECKING
P11BF Cam Shift Actuator Outlet "A" Cylinder 1 Range/Performance	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 1 -F366-. Refer to Cam Adjustment Actuators --, CHECKING
P11C0 Cam Shift Actuator Outlet "B" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 2 -F367-. Refer to Cam Adjustment Actuators --, CHECKING
P11C1 Cam Shift Actuator Outlet "A" Cylinder 2 Range/Performance	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 3 -F368-. Refer to Cam Adjustment Actuators --, CHECKING
P11C2 Cam Shift Actuator Outlet "B" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 4 -F369-. Refer to Cam Adjustment Actuators --, CHECKING
P11C3 Cam Shift Actuator Outlet "A" Cylinder 3 Range/Performance	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 5 -F370-. Refer to Cam Adjustment Actuators --, CHECKING
P11C4 Cam Shift Actuator Outlet "B" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 6 -F371-. Refer to Cam Adjustment Actuators --, CHECKING
P11C5 Cam Shift Actuator Outlet "A" Cylinder 4 Range/Performance	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 7 -F372-. Refer to Cam Adjustment Actuators --, CHECKING
P11C6 Cam Shift Actuator Outlet "B" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) short to battery plus	Power stage temperature> 160 - 200° C Or Output current driver stage internal value (hardware values)	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuator 8 -F373-. Refer to Cam Adjustment Actuators --, CHECKING
P12A1 Fuel Rail Pressure Sensor Inappropriately Low	Fuel System Pressure Sensor, High Pressure Side Rationality Check Low	Deviation lambda of controller included adaptation< -22.50% and high pressure controller output> 40mg	General: Engine speed512 - 6, 816 rpm Fuel mass setpoint5.00 - 1, 389.00mg/rev Time after change to DFInot equippeds Time after engine start> 10.0 s Engine warm-upnot active Catalyst heatingnot active Full loadnot active Catalyst purgenot active Lambda controlclosed loop Evap purge functionality diagnosis not active Fuel pressure setpoint gradient<= 34, 777.60 [kPa And Depending on low dynamic conditions: Fuel mass setpoint lower range> 5.00 mg/rev For time>= 10.0s Fuel mass setpoint upper range< 187.17 - 229.23mg/rev Fuel mass setpoint gradient-1, 389.00 - 1, 389.00 mg/rev For time>= 5.0 s And Depending on canister purge: Canister load<= 1.00[-] Or Evap purge valvenot active or closed	5.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .-- Check the Fuel Pump Control Module -J538- / Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .-- Check the fuel pressure. Refer to appropriate repair information.
P12A2 Fuel Rail Pressure Sensor Inappropriately High	Fuel System Pressure Sensor, High Pressure Side Rationality Check High	Deviation lambda of controller included adaptation> 30.00% And High pressure controller output< -35 mg	General: Engine speed608 - 6, 816 rpm Fuel mass setpoint5.00 - 1, 389.00 mg/rev Time after change to DFInot equipped s Time after engine start> 10.0 s Engine warm-upnot active Catalyst heatingnot active Full loadnot active Catalyst purgenot active Lambda controlclosed loop Evap purge functionality diagnosis not active Fuel pressure setpoint gradient<= 34, 777.60 [kPa And Depending on low dynamic conditions: Fuel mass setpoint lower range> 5.00 mg/rev For time>= 10.0s Fuel mass setpoint upper range< 187.17 - 229.23mg/rev Fuel mass setpoint gradient-1, 389.00 - 1, 389.00 mg/rev For time>= 5.0 s And Depending on canister purge: Canister load<= 1.00[-] Or Evap purge valvenot active or closed	5.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .-- Check the Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .-- Check the fuel pressure. Refer to appropriate repair information.
P12A4 Fuel Rail Pump Control Valve Stuck Closed	Fuel System Pressure Sensor, High Pressure Side Out Of Range High	Deviation between fuel pressure setpoint and current fuel pressure< -2999.90 kPa Deviation lambda of controller included adaption-50.00 - 50.00 % Case 1: High pressure controller output< -45 mg Case 2: Flow control valveopen Mass fuel flow setpoint> 15.01mg/rev	General: Engine speed608 - 6, 816 rpm Fuel mass setpoint5.00 - 1, 389.00 mg/rev Time after engine start> 10.0 s Engine warm-upnot calibrated Catalyst heatingnot calibrated Full loadnot calibrated Catalyst purgenot calibrated Lambda controlnot calibrated Evap purge functionality diagnosis not calibrated Fuel pressure setpoint gradient<= 34, 777.60 [kPa And Depending on low dynamic conditions: Fuel mass setpoint lower range> 5.00 mg/rev For time>= 10.0 s Fuel mass setpoint upper range< 187.17 - 229.23mg/rev Fuel mass setpoint gradient-1, 389.00 - 1, 389.00 mg/rev For time>= 5.0 s And Depending on canister purge: Canister loadnot calibrated[-] Or Evap purge valvenot calibrated	5.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor -G247-, CHECKING .-- Check the Fuel Delivery Unit -GX1-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING .-- Check the fuel pressure. Refer to appropriate repair information.
P13EA Cold Start Ignition Timing Performance Off Idle	Ignition Control Ignition Timing Monitor	Ratio between ignition angle efficiency integral and time at part load > 0.16 [-]	Time @ part load > 5.0 s Ignition angle set point <= 0.94 [-] Engine part load Vehicle speed > 2 mph And Diff. air mass set point vs. filtered air mass set point for load dynamic detection < 99.999.0 mg/rev For time >= 0.0 s And Diff. engine speed vs. filtered engine speed for engine speed dynamic detection < 8, 160 RPM For time >= 0.0 s	0.1 s Once / DCY	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor -G28-, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .-- Check for any Engine Speed sensor or Ignition Coil faults and diagnose them first.-- If NO other codes are set, check the ECM. Refer to appropriate repair information.
P1545 Throttle Actuator "A" Control Motor Circuit Range/Performance	Throttle Actuator Out Of Range	Control duty cycle > 98.0 %	Throttle position not at min. value Throttle adaptation not active Throttle actuator commanded on	5.0 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
Throttle Actuator Rationality Check		Difference between throttle position set point and throttle flap opening angle for electronic throttle control > 2.998 - 24.982° TPS	Throttle adaptation (@ initial start or after detection of throttle exchange or checksum error) not active Throttle actuator commanded on Difference between throttle position set point and throttle flap opening angle <= 1.999; > -1.999° TPS
P169A Loading Mode Active	ECM: Transport Mode Function Monitoring: Mode Change	Transport mode active	Vehicle speed < 3 mph Max trip mileage since initial vehicle start-up < 62.15 miles During ECM keep alive-time after ignition off engine speed 0 RPM Production mode not active For hybrid: Drive motor off	0.01 s Continuous	1 DCY	-- Perform readiness check. Refer to READINESS CODES .
P2004 Intake Manifold Runner Control Stuck Open Bank 1	Intake Manifold Runner Flap Actuator Stuck Open	Signal voltage > 1.89 V For time >= 1.5 s	Flap commanded off Time after engine start > 5.0 s	0.2 s Continuous	2 DCY	-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve -N316-, CHECKING .
P2006 Intake Manifold Runner Control Stuck Closed Bank 1	Intake Manifold Runner Flap Actuator Stuck Close	Signal voltage < 3.10 V For time >= 1.5 s	Flap commanded on Time after engine start > 5.0 s	0.2 s Continuous	2 DCY	-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve -N316-, CHECKING .
P2008 Intake Manifold Runner Control Circuit/Open Bank 1	Intake Manifold Runner Flap Actuator Open Circuit	Output voltage lower range 1.92 - 2.21 V Output voltage upper range (hardware values) 2.85 - 3.25 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve -N316-, CHECKING .
P2009 Intake Manifold Runner Control Circuit Low Bank 1	Intake Manifold Runner Flap Actuator Short To Ground	Output voltage (hardware values) < 1.92 - 2.21 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve -N316-, CHECKING .
P2010 Intake Manifold Runner Control Circuit High Bank 1	Intake Manifold Runner Flap Actuator Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current (hardware values) driver stage internal value	Engine running Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve -N316-, CHECKING .
P2014 Intake Manifold Runner Position Sensor/Switch Circuit Bank 1	Intake Manifold Runner Flap Position Sensor Short To Ground / Open Circuit	Intake manifold runner flap position sensor voltage < 0.20 V	Engine start not active	0.04 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor -G336-, CHECKING .
P2015 Intake Manifold Runner Position Sensor/Switch Circuit Range/Performance Bank 1	Intake Manifold Runner Flap Actuator Adaptation Value Monitoring	Diff. actual value vs. substitution value @ lower mechanical thresh hold > 0.70 V Or Diff. actual value vs. substitution value @ upper mechanical thresh hold > 0.70 V Failed adaptations >= 1.00 [-]	Modeled air temperature < 0.75 [-] Engine running Engine speed > 640; < 1, 504 RPM ECT @ cylinder head > -30° C Intake manifold runner flap adaptation not finished	0.04 s Once per lifetime	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor -G336-, CHECKING .
P2017 Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1	Intake Manifold Runner Flap Position Sensor Short To Battery Voltage	Intake manifold runner flap position sensor voltage > 4.80 V	Engine start not active	0.04 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor -G336-, CHECKING .
P2024 EVAP Fuel Vapor Temperature Sensor Circuit	Smart Temperature Sensor Open Circuit	NVLD output voltage lower range >= 1.92 - 2.21 V NVLD output voltage upper range <= 2.85 - 3.25 V	Case 1: Ignition on Case 2: Ignition off (during ECM keep alive-time)	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P2025 EVAP Fuel Vapor Temperature Sensor Performance	Smart Temperature Sensor Functional Check*	Diff. time between ECU and smart module > 3.0 s	Ignition off ECM keep alive time active	3.0 s Once / DCY	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
Reset counter > 3.00 [-]			Engine running Last ECM keep alive mode finished	0.1 s Once / DCY	3 DCY
Smart Temperature Sensor Out Of Range High*		Smart module temperature > 119° C	Ignition off NVLD (EVAP-System) diagnostic mode = active Fuel level < 85.10%	300 s Continuous	2 DCY
			Engine Running			30 s Continuous
Smart Temperature Sensor Out Of Range Low*		Smart module temperature < -39° C	Engine off time >= 360.00 min ECT @ cylinder head > -23° C IAT cross check finished ECT cross check finished Fuel level < 85.10%	1.0 s Once / DCY
Smart Temperature Sensor Cross Check*		Difference between smart temperature and ECT @ cylinder head >= 25.5 K And Difference between smart temperature @ engine start and IAT @ manifold >= 25.5 K	Engine off time >= 360.00 min IAT cross check finished ECT cross check finished Fuel level < 85.10%
Smart Temperature Sensor Signal Dynamic Check*		Gradient smart temperature > 20 K/10min	Ignition off Fuel level < 85.10 % NVLD (EVAP-System) diagnostic mode active	300 s Once / DCY
Smart Temperature Sensor Communication with Smart Temperature Sensor*		Response time > 1.0 s And Number of checks > 3.00 [-] Or Security bit incorrect And Number of checks > 3.00 [-]	Case 1: Ignition on Engine running Case 2: Ignition off (during ECM keep alive-time)	5.0 s Continuous
P2026 EVAP Fuel Vapor Temperature Sensor Circuit Low Voltage	Smart Temperature Sensor Short To Ground	NVLD output voltage < 1.92 - 2.21 V	Case 1: Ignition on Case 2: Ignition off (during ECM keep alive-time)	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P2027 EVAP Fuel Vapor Temperature Sensor Circuit High Voltage	Smart Temperature Sensor Short To Battery Voltage	NVLD output temperature > 160.0 - 200.0° C Or NVLD output current driver stage internal value	Case 1: Ignition on Case 2: Ignition off (during ECM keep alive-time)	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-. Refer to Fuel Tank Leak Detection Control Module -J909- / Fuel Tank Pressure Sensor -G400-, CHECKING .
P2067 Fuel Level Sensor "B" Circuit Low	COM: Fuel Level (FL) Sensor 2 communication with IPC	Instrument cluster module signal: short to groundfailure Instrument cluster module signal: signal range checkfailure		0.5 s Continuous	2 DCY	-- Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P2068 Fuel Level Sensor "B" Circuit High	COM: Fuel Level (FL) Sensor 2 communication with IPC	Instrument cluster module signal: short to battery / open circuitfailure		0.5 s Continuous	2 DCY	-- Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P2088 "A" Camshaft Position Actuator Control Circuit Low Bank 1	VVT Actuator Intake Short To Ground	Output voltage (hardware values) < 1.92 - 2.21 V	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 -N205-, CHECKING .
P2089 "A" Camshaft Position Actuator Control Circuit High Bank 1	VVT Actuator Intake Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current (hardware values) driver stage internal value	Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 -N205-, CHECKING .
P2090 "B" Camshaft Position Actuator Control Circuit Low Bank 1	Variable Valve Timing (VVT) Exhaust Actuator short to ground	Output voltage< 1.92 - 2.21 V (hardware values)	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 -N318-, CHECKING
P2091 "B" Camshaft Position Actuator Control Circuit High Bank 1	Variable Valve Timing (VVT) Exhaust Actuator short to battery plus	Power stage temperature > 160 - 200° C Or Output currentdriver stage internal value (hardware values)	Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 -N318-, CHECKING
P2096 Post Catalyst Fuel Trim System Too Lean Bank 1	Fuel System Out Of Range Low	Adaptation value < 0.05 [-]	2nd lambda control n.a. Catalyst purge not active Injection mode change (DFI/MFI)not active Engine speed >= 896 RPM Integrated mass for fuel in oil < 255.00 [-] Choice of: O2S rear (binary) check not active Or O2S rear (binary) check finished	0.0 s Continuous	2 DCY	-- Check exhaust system visually for leaks first and correct as necessary.-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P2097 Post Catalyst Fuel Trim System Too Rich Bank 1	Fuel System Out Of Range High	Adaptation value > -0.05 [-]	2nd lambda control n.a. Catalyst purge not active Injection mode change (DFI/MFI)not active Engine speed >= 896 RPM Integrated mass for fuel in oil < 255.00 [-] Choice of: O2S rear (binary) check not active Or O2S rear (binary) check finished	0.0 s Continuous	2 DCY	-- Check exhaust system visually for leaks first and correct as necessary.-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P2100 Throttle Actuator "A" Control Motor Circuit/Open	Throttle Actuator Open Circuit	Electronic throttle valve driver load resistance > 200.0 kOhm	Difference between measured and filtered throttle position <= 0.073° TPS Actuator commanded off	0.1 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P2101 Throttle Actuator "A" Control Motor Circuit Range/Performance	Throttle Actuator Over Temperature	Electronic throttle valve driver temperature (hardware values) > 170.0 - 190.0° C	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P2103 Throttle Actuator "A" Control Motor Circuit High	Throttle Actuator Short Circuit	Electronic throttle valve driver current (hardware values) driver stage internal value	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module -GX3-, CHECKING .
P2122 Throttle/Pedal Position Sensor/Switch "D" Circuit Low	Accelerator Pedal Position Sensor 1 Out Of Range Low	Signal voltage sensor 1 < 0.40 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module -GX2-, CHECKING .
P2123 Throttle/Pedal Position Sensor/Switch "D" Circuit High	Accelerator Pedal Position Sensor 1 Out Of Range High	Signal voltage sensor 1 > 4.82 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module -GX2-, CHECKING .
P2127 Throttle/Pedal Position Sensor/Switch "E" Circuit Low	Accelerator Pedal Position Sensor 2 Out Of Range Low	Signal voltage sensor 2 < 0.20 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module -GX2-, CHECKING .
P2128 Throttle/Pedal Position Sensor/Switch "E" Circuit High	Accelerator Pedal Position Sensor 2 Out Of Range High	Signal voltage sensor 2 > 2.80 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module -GX2-, CHECKING .
P2138 Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation	Accelerator Pedal Position Sensor 1 And 2 Rationality Check	Difference between signal voltage sensor 1 and sensor 2 > 0.10 - 0.12 V		0.4 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module -GX2-, CHECKING .
P2177 System Too Lean Off Idle Bank 1	Fuel System Direct Fuel Injection System Too Lean	Adaptive value >= 28.0 %	MAF > 60.0 mg/rev ECT @ cylinder head > 20° C IAT @ manifold > -48° C AAT > -48° C Lambda set point 0.95 - 1.05 [-] Lambda control closed loop Integrated MAF >= 600.0 - 10, 000.0 g Fuel mass15.01 - 50.00 mg/rev Engine speed1, 024 - 3, 744 rpm Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection< 60 - 130 rpm Diff. air mass vs. averaged air mass for load dynamic detection< 16.00 - 30.01 mg/rev Diff. between reference and actual fuel pressure, high side<= 2000.10 kPa Integrated air mass> 5.0 - 25.0 g And Evap purge valve closed or canister load<= 1.20[-] Evap purge flowat max. value Or Dependence on canister purge min: Lower limit of lambda controller outputn.a. Or Upper limit of lambda controller outputn.a. And Evap purge flowat min. value	5.0 s Continuous	2 DCY	-- Check the intake and vacuum hoses visually for leaks. Check the Positive Crankcase Ventilation visually. Also make sure the oil dipstick is properly secured.-- Listen to and visually inspect the exhaust system to insure there are no leaks.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 -N80-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2178 System Too Rich Off Idle Bank 1	Fuel System Direct Fuel Injection System Too Rich	Adaptive value <= -30.0 %	Air mass> 60.00 mg/rev ECT @ cylinder head> 20° C IAT @ manifold> -48° C AAT> -48° C Lambda setpoint0.97 - 1.05[-] Lambda controlclosed loop Integrated air mass>= 600.0 - 10, 000.0g Fuel mass15.01 - 50.00mg/rev Engine speed1, 024 - 3, 744 rpm Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection< 60 - 130 rpm Diff. air mass vs. averaged air mass for load dynamic detection< 16.00 - 30.01 mg/rev Diff. between reference and actual fuel pressure, high side<= 2, 000.10 kPa Integrated air mass> 5.0 - 25.0 g And Evap purge valve closed Or Canister load<= 1.20[-] Evap purge flowat max. value Or Dependence on canister purge min: Lower limit of lambda controller outputn.a. Or Upper limit of lambda controller outputn.a. And Evap purge flowat min. value	5.0 s Continuous	2 DCY	-- Check the Evaporative Emission (EVAP) System visually for contamination.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2181 Cooling System Performance	Engine Cooling System Rationality Check	Modeled ECT @ cylinder head > 66 - 70° C Choice of: ECT @ cylinder head < 65 - 69° C Or ECT @ radiator outlet < n.a.° C	ECT @ cylinder head @ first start >= -10° C ECT @ cylinder head @ first start <= 50 - 55° C AAT > -10° C Ratio fuel cut off <= 10.16 % Ratio accumulated time engine load condition vs. time since engine start <= 39.84 % Determination engine load condition: Engine load (lower threshold)<= 2.50% engine load (upper threshold)>= 100.00% Ratio accumulated time high speed condition<= 14.84 % Determination high speed condition: Vehicle speed> 75mph Ratio accumulated time start-stop active<= 16.02 % Setpoint of RVC in measurement window< 99.61 % Case 1: Engine speed< 8, 160rpm Case 2: Engine speed>= 8, 160 rpm Diff. ECT@ cylinder head during measurement< 256° C For time>= 0.0 s	1.0 s Once / DCY	2 DCY	-- Check cooling system visually for leaks or damaged components.-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator -N493-, CHECKING .-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor -G62-, CHECKING .
Electrical Thermostat Rationality Check		ECT @ cylinder head < 60° C For time >= 0.0 s	Engine running Or Engine stopped And ECT @ cylinder head once after start > 65° C Or ECT @ radiator outlet once after engine startnot calibrated[°C] And AAT sensor signal valid AAT > -10° C Relative actual MAF > 5.00 % ECT @ cylinder head @ first start lower limit >= -40° C ECT @ cylinder head @ first start upper limit<= 215[°C] Vehicle speed >= 0 mph Modeled ECT @ cylinder head > 60° C Start-stop cycles <= 255.00 [-] For time >= 15.0 s
P2183 Engine Coolant Temperature Sensor 2 Circuit Range/Performance	Engine Coolant Temperature Sensor @ Radiator Outlet Cross Check	High side: reference measuring Diff. ECT @ radiator outlet @ cold start vs. IAT @ manifold @ cold start> 25.0 K Diff. ECT @ radiator outlet @ cold start vs. ECT @ cylinder head @cold startn.a. K Diff. ECT @ radiator outlet @ cold start vs. AAT @ cold start> 25.0 K Min. amount of faulty reference measurements to detect defective sensor2.00[-] Or Low side: reference measuring Diff. IAT @ manifold @ cold start vs. ECT @ radiator outlet @ cold start> 25.0 K Diff. ECT @ cylinder head @ cold start vs. ECT @ radiator outlet @cold startn.a. K Diff. AAT @ cold start vs. ECT @ radiator outlet @ cold start> 25.0 K Min. amount of faulty reference measurements to detect defective sensor2.00[-]	Engine off time>= 360.00 min Engine off timeplausible Time after engine start<= 1, 400.0 s Depending on temperature slope Diff. actual vs previous IAT< 256.0 K Diff. actual vs previous ECT@ cylinder headn.a.K Diff. actual vs previous ECT@ radiator outlet< 256.0K Diff. actual vs previous AAT< 256.0 K For time>= 1.0 s Depending on mean value condition Mean value of all temperature sensors @ cold start>= -256° C Number of valid sensors>= 2.00[-] Depending on block heater / solar radiation detection Time after engine start>= 0.5 s Vehicle speed>= 22 mph For time>= 20.0 s Diff. actual IAT @ manifold vs. min. IAT @ manifold< 5.0 K Diff. actual ECT @ cylinder head vs. min. ECT @ cylinder headn.a.K Diff. actual AAT vs. min. AAT< 4.0 K Diff. actual ECT @ radiator outlet vs. min. ECT @ radiator outlet< 1.1 K	0.1 s Once / DCY	2 DCY	-- Check the Engine Coolant Temperature Sensor On Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet -G83-, CHECKING .
P2184 Engine Coolant Temperature Sensor 2 Circuit Low	Engine Coolant Temperature Sensor @ Radiator Outlet Short To Ground	Sensor voltage < 0.30 V		0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor On Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet -G83-, CHECKING .
P2185 Engine Coolant Temperature Sensor 2 Circuit High	Engine Coolant Temperature Sensor @ Radiator Outlet Short To Battery / Open Circuit	Sensor voltage > 4.90 V	IAT @ throttle >= -33° C Time after engine start > 60 s	0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor On Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet -G83-, CHECKING .
P2187 System Too Lean at Idle Bank 1	Fuel System Direct Fuel Injection System Too Lean	Case 1: Adaptive value >= 3.01 mg/rev Case 2: Adaptive value n.a.	Air mass> 60.00mg/rev ECT @ cylinder head> 20° C IAT @ manifold> -48° C AAT> -48° C Lambda setpoint0.97 - 1.05[-] Lambda controlclosed loop Integrated air mass>= 600.0 - 10, 000.0 g Vehicle speed< 4mph Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection< 60 - 130 rpm Diff. air mass vs. averaged air mass for load dynamic detection< 16.00 - 30.01mg/rev Diff. between reference and actual fuel pressure, high side<= 2000.10 kPa Integrated air mass> 5.0 - 25.0 g And Fuel mass lower range> 4.01 mg/rev Fuel mass upper range< 17.00 - 19.01mg/rev Engine speed704 - 927[rpm] Or Engine n.a. And Evap purge valve closed Or Canister load<= 1.20[-] Evap purge flowat max. value Or Depending on canister purge min: Lower limit of lambda controller outputn.a. Or Upper limit of lambda controller outputn.a. And Evap purge flowat min. value	5.0 s Continuous	2 DCY	-- Check the intake and vacuum hoses visually for leaks. Check the Positive Crankcase Ventilation visually. Also make sure the oil dipstick is properly secured.-- Listen to and visually inspect the exhaust system to insure there are no leaks.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 -N80-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2188 System Too Rich at Idle Bank 1	Fuel System Direct Fuel Injection System Too Rich	Case 1: Adaptive value <= -3.01 mg/rev Case 2: Adaptive value <= n.a. kg/h	Air mass> 60.00mg/rev ECT @ cylinder head> 20° C IAT @ manifold> -48° C AAT> -48° C Lambda setpoint0.97 - 1.05[-] Lambda controlclosed loop Oil dilutionnot detected Integrated air mass>= 600.0 - 10, 000.0 g Vehicle speed< 4 mph Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection< 60 - 130 rpm Diff. air mass vs. averaged air mass for load dynamic detection< 16.00 - 30.01 mg/rev Diff. between reference and actual fuel pressure, high side<= 2000.10 kPa Integrated air mass> 5.0 - 25.0 g And Fuel mass lower range> 4.01 mg/rev Fuel mass upper range< 17.00 - 19.01 mg/rev Engine speed704 - 927 rpm Or Engine n.a. And Evap purge valve closed Or Canister load<= 1.20[-] Evap purge flowat max. value Or Depending on canister purge min: Lower limit of lambda controller outputn.a. Or Upper limit of lambda controller outputn.a. And Evap purge flowat min. value	5.0 s Continuous	2 DCY	-- Check the Evaporative Emission (EVAP) System visually for contamination.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2195 O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1	Oxygen Sensors Front Rationality Check	Plausibility signal check O2S front and O2S rear: Lambda value > 1.15 [-] And O2S signal rear >= 0.91 [V]	O2S front ready O2S rear ready ECT @ cylinder head >= -48° C MAF > 0.0; < 2, 047.0 kg/h Catalyst purge not active Integrated MAF after end of catalyst purge 10.0 g Engine speed > 0 RPM Modeled EGT @ O2S front > -273; < 850° C Integrated MAF > 40.0 g Dynamic lambda controller output < 3.0 % Dynamic MAF < 0.05 g/rev Dynamic engine speed < 200 RPM And Second control loop active: MAF 0.06 - 0.75 g/rev Engine speed 576 - 4512 RPM	67.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P2196 O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1	Oxygen Sensors Front Rationality Check	Plausibility signal check O2S front and O2S rear: Lambda value < 0.85 [-] And O2S signal rear >= 0.17 V	O2S frontready O2S rearready ECT @ cylinder head>= -48° C MAF> 0.00; < 2047.97 kg/h Catalyst purgenot active Integrated air mass after end of catalyst purge10.0 g Engine speed> 0rpm Modeled EGT @ O2S front> -273; < 850° C Injection mode change (DFI/MFI)not active Integrated air mass> 40.0 g Dynamic lambda controller output< 3.00 % Dynamic air mass< 0.05 g/rev Dynamic engine speed< 200 rpm And Second control loop active: Air mass 0.06 - 0.75 g/rev Engine speed576 - 4, 512 rpm	67.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P219C Cylinder 1 Air-Fuel Ratio Imbalance	Air Fuel Imbalance Monitoring Out Of Range High	Cylinder 1: Weighted adaptive value > 10.0 %	Fuel pressure setpointnot calibrated kPa Modeled catalyst temperature @ start <= 850° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Cylinder shut off not active AAT >= -48° C Barometric pressure >= 73.0 kPa min. injection time not reached And Choice of: Catalyst diagnosis n.a. Or Catalyst diagnosis n.a. Depending on catalyst diagnosis: Canister purge (conditions) n.a. Or Evap purge valve n.a. Or Evap purge n.a. And O2S dynamic diagnosis n.a. O2S delay diagnosis n.a. Lambda control closed loop Catalyst purge not active Canister load <= 2.00 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.00 [-] Segments after start > 0.00 [-] Time after engine start > 0.0 s Rough road not detected Min. fuel mass>= 0.00 mg/rev Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear not active And Integrated MAF >= 1.0 - 12.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. MAF vs. dynamic MAF < 29.99 mg/rev ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255 [-] Engine speed 1, 312 - 3, 008 RPM And Mass fuel flow lower range >= 11.00 mg/rev Mass fuel flow upper range <= 32.00 mg/rev	90 s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Air Fuel Imbalance Monitoring Out Of Range Low		Cylinder 1: Weighted adaptive value < -15.0 %
P219D Cylinder 2 Air-Fuel Ratio Imbalance	Air Fuel Imbalance Monitoring Out Of Range High	Cylinder 1: Weighted adaptive value > 10.0 %	Fuel pressure setpointnot calibrated kPa Modeled catalyst temperature @ start <= 850° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Cylinder shut off not active AAT >= -48° C Barometric pressure >= 73.0 kPa Min. injection time not reached And Choice of: Catalyst diagnosis n.a. Or Catalyst diagnosis n.a. Depending on catalyst diagnosis: Canister purge (conditions) n.a. Or Evap purge valve n.a. Or Evap purge n.a. And O2S dynamic diagnosis n.a. O2S delay diagnosis n.a. Lambda control closed loop Catalyst purge not active Canister load <= 2.00 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.00 [-] Segments after start > 0.00 [-] Time after engine start > 0.0 [s] Rough road not detected Min. fuel mass>= 0.00 mg/rev Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear not active And Integrated MAF >= 1.0 - 12.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. MAF vs. dynamic MAF < 29.99 mg/rev ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255 [-] Engine speed 1, 312 - 3, 008 RPM And Mass fuel flow lower range >= 11.00 mg/rev Mass fuel flow upper range <= 32.00 mg/rev	90 s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Air Fuel Imbalance Monitoring Out Of Range Low		Cylinder 2: Weighted adaptive value < -15.0 %
P219E Cylinder 3 Air-Fuel Ratio Imbalance	Air Fuel Imbalance Monitoring Out Of Range High	Cylinder 1: Weighted adaptive value > 10.0 %	Fuel pressure setpointnot calibrated[kPa] Modeled catalyst temperature @ start <= 850° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Cylinder shut off not active AAT >= -48° C Barometric pressure >= 73.0 kPa Min. injection time not reached And Choice of: Catalyst diagnosis n.a. Or Catalyst diagnosis n.a. Depending on catalyst diagnosis: Canister purge (conditions) n.a. Or Evap purge valve n.a. Or Evap purge n.a. And O2S dynamic diagnosis n.a. O2S delay diagnosis n.a. Lambda control closed loop Catalyst purge not active Canister load <= 2.00 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.00 [-] Segments after start > 0.00 [-] Time after engine start > 0.0 [s] Rough road not detected Min. fuel mass>= 0.00[mg/rev] Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear not active And Integrated MAF >= 1.0 - 12.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. MAF vs. dynamic MAF < 29.99 mg/rev ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255 [-] Engine speed 1, 312 - 3, 008 RPM And Mass fuel flow lower range >= 11.00 mg/rev Mass fuel flow upper range <= 32.00 mg/rev	90 s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Air Fuel Imbalance Monitoring Out Of Range Low		Cylinder 3: Weighted adaptive value < -15.0 %
P219F Cylinder 4 Air-Fuel Ratio Imbalance	Air Fuel Imbalance Monitoring Out Of Range High	Cylinder 1: Weighted adaptive value > 10.0 %	Fuel pressure setpointnot calibrated[kPa] Modeled catalyst temperature @ start <= 850° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Cylinder shut off not active AAT >= -48° C Barometric pressure >= 73.0 kPa Min. injection time not reached And Choice of: Catalyst diagnosis n.a. Or Catalyst diagnosis n.a. Depending on catalyst diagnosis: Canister purge (conditions) n.a. Or Evap purge valve n.a. Or Evap purge n.a. And O2S dynamic diagnosis n.a. O2S delay diagnosis n.a. Lambda control closed loop Catalyst purge not active Canister load <= 2.00 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.00 [-] Segments after start > 0.00 [-] Time after engine start > 0.0 [s] Rough road not detected Min. fuel mass>= 0.00[mg/rev] Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear not active And Integrated MAF >= 1.0 - 12.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. MAF vs. dynamic MAF < 29.99 mg/rev ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255 [-] Engine speed 1, 312 - 3, 008 RPM And Mass fuel flow lower range >= 11.00 mg/rev Mass fuel flow upper range <= 32.00 mg/rev	90 s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
Air Fuel Imbalance Monitoring Out Of Range Low		Cylinder 4: Weighted adaptive value < -15.0 %
P2237 O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1	Oxygen Sensors Front Open Circuit Pump Voltage (VIP)	Diff. pump voltage (VIP) vs. virtual ground voltage (VG) <= 1.20 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) <= 1.20 V And Choice of: Nernst voltage (VN) > 4.40 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG) > 2.35 V Diff. pump voltage (VIP) vs. virtual ground voltage (VG) < -2.35 V Or Diff. nernst voltage (VN) vs. virtual ground voltage (VG) > 1.60 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) < -0.10 V Or Pump current driver stage internal value Or Measurement WRAF sensor label resistor > n.a. Ohm	O2S front (linear) ready O2S ceramic temperature> 785° C For time>= 10.0s	2.3 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P2243 O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1	Oxygen Sensors Front Open Circuit Nernst Voltage (VN)	Diff. pump voltage (VIP) vs. virtual ground voltage (VG) <= 1.20 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) <= 1.20 V And Choice of: Nernst voltage (VN) > 4.40 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG) > 2.35 V Diff. pump voltage (VIP) vs. virtual ground voltage (VG) < -2.35 V Or Diff. nernst voltage (VN) vs. virtual ground voltage (VG) > 1.60 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) < -0.10 V Or Pump currentdriver stage internal value Or Measurement WRAF sensor label resistor > n.a. Ohm	O2S front (linear) ready O2S ceramic temperature> 785° C For time>= 10.0s	2.3 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P2251 O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1	Oxygen Sensors Front Open Circuit Virtual Ground (VG)	Nernst voltage (VN) > 4.40 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG) > 2.35 V Diff. pump voltage (VIP) vs. virtual ground voltage (VG) < -2.35 V Or Diff. nernst voltage (VN) vs. virtual ground voltage (VG) > 1.60 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) < -0.10 V Or Pump current driver stage internal value Or Measurement O2S front label resistor > n.a. Ohm And Choice of: Diff. pump voltage (VIP) vs. virtual ground voltage (VG) <= 1.20 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) <= 1.20 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG)> 1.20V Diff. nernst voltage (VN) vs. virtual ground voltage (VG)> 1.20V	O2S front (linear) ready O2S ceramic temperature> 785° C For time>= 10.0 s	2.3 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P2257 AIR System Control "A" Circuit Low	Secondary Air Injection Pump Relay Short To Ground	Output voltage (hardware values) 1.92 - 2.21 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-. Refer to Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-, CHECKING .
P2258 AIR System Control "A" Circuit High	Secondary Air Injection Pump Relay Short To Battery Plus	Actuator temperature > 160 - 200° C Or Output current (hardware values) driver stage internal value	Engine running Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-. Refer to Secondary Air Injection Pump Motor -V101- / Secondary Air Injection Pump Relay -J299-, CHECKING .
P2270 O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 2	Oxygen Sensors Rear Signal Range Check	Max. O2S rear voltage < 0.87 V Intrusive lambda ramp lean< 0.85[-]	General conditions: Catalyst monitor lambda modulation requestactive Vehicle speed>= 19 mph Barometric pressure>= 0.00 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rearready O2S frontready ECT @ cylinder head> 60° C IAT @ manifold> -48° C Modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff. between dynamic and stationary catalyst temperature-150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear<= 900° C MAF per cylinder22.50 - 150.00 kg/h Air mass, lower range>= 0.00 mg/rev Air mass, upper range<= 650.00 - 1389.00 mg/rev And Engine loadn.a.% Air mass setpointn.a. mg/rev Accelerator pedal valuen.a. % For timen.a. s And Low dynamic conditions Dynamic engine speed< 50 rpm Dynamic air mass< 50.00 mg/rev Dynamic lambda controller output< 20.00 % And Integrated air mass after dynamic conditions are fulfilled> 20.0 g Time after a catalyst purge phase>= 1.0 s O2S rear voltage @ diagnosis start>= 0.55 V Integrated air mass>= 0.0 g Integrated heat energy>= 550.00 - 700.00 kJ Engine speed1, 088 - 3, 008 rpm Deviation of lambda controller output< 50.00 % Proportional part of secondary fuel control loopnot calibrated % Coasting functionnot active O2S heater rearactive Lambda adaptationnot active Valve liftnot active And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis< 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis< 0.25[-] Depending on canister purge: Canister loadn.a.[-] Evap purge flown.a. Or Canister load calculationn.a. Evap purge flown.a. Or Evap purge valven.a. Or Evap purge valven.a. Or Evap purgen.a. Or Depending on canister purge closing: Canister purge (conditions)n.a. Canister purge valve (closing time)n.a.[s] And Choice of: evap purge valven.a. Or Evap purge valven.a. And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.40 - 1.80 kg	0 (FTP75: 50) s Once / DCY	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P2271 O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 2	Oxygen Sensors Rear Signal Range Check	O2S rear voltage> 0.25V Intrusive lambda ramp lean> 1.12[-]	General conditions: Catalyst monitor lambda modulation requestactive Intrusive lambda ramp requestactive Vehicle speed>= 19 mph Barometric pressure>= 0.00 kPa Catalyst overheating protectionnot active Turbine overheating protectionnot active O2S rearready O2S frontready ECT @ cylinder head> 60° C IAT @ manifold> -48° C Modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff. between dynamic and stationary catalyst temperature-150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear<= 900° C MAF per cylinder22.50 - 150.00 kg/h Air mass, lower range>= 0.00 mg/rev Air mass, upper range<= 650.00 - 1, 389.00 mg/rev And Engine loadn.a.% Air mass setpointn.a. g/rev Accelerator pedal valuen.a. % For time n.a. s And Low dynamic conditions Dynamic engine speed< 50 rpm Dynamic air mass< 50.00mg/rev Dynamic lambda controller output< 20.00 % And Integrated air mass after dynamic conditions are fulfilled> 20.0 g Time after a catalyst purge phase>= 1.0 s O2S rear voltage>= 0.55 V Integrated air mass>= 0.0 g Integrated heat energy>= 550.00 - 700.00 kJ Engine speed1, 088 - 3, 008 rpm Deviation of lambda controller output< 50.00 % Proportional part of secondary fuel control loop not calibrated % Coasting functionnot active O2S heater rearactive Lambda adaptationnot active Valve liftnot active And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis< \| 0.10 \|[-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis< \| 0.25 \|[-] Depending on canister purge: Canister loadn.a.[-] Evap purge flown.a. Or Canister load calculationn.a. Evap purge flown.a. Or Evap purge valven.a. Or Evap purge valven.a. Or Evap purgen.a. Or Depending on canister purge closing: Canister purge (conditions)n.a. Canister purge valve (closing time)n.a.[s] And Choice of: Evap purge valven.a. Or Evap purge valven.a. And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.40 - 1.80 kg	0 (FTP75: 50) s Once / DCY	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING .
P2279 MAP/MAF - Throttle Position Correlation	Intake Air System Rationality Check	Filtered lambda controller included correction and adaptation -30.0 - 30.0 % Lambda control active And Deviation throttle area controller > 60.0 %	Throttle position > 0.0° TPS Throttle position < 100.003° TPS Engine speed > 576; < 3, 008 RPM Modeled pressure quotient > 0.27; < 0.57 [-] Engine running Throttle actuator commanded on Time after engine start > 5.0 s Throttle position sensor failure not detected Fuel cut off not active Fast throttle adaptation finished Gradient intake manifold pressure -199.90 - 199.90 kPa/s Engine speed limitation not active Barometric pressure plausibility diagnosis finished Intake manifold modeled adaption active And Choice of: MAF sensor active Or Manifold pressure sensor active And Choice of: Pressure upstream throttle < 135.0 kPa Or Pressure upstream throttle not active And Choice of: Barometric pressure > 73.00; < 107.50 kPa Or Barometric pressure sensor not active	5.0 s Continuous	2 DCY	-- Check visually for air leaks between intake and throttle body, oil fill cap not tight or oil dipstick not seated in tube.-- Also visually inspect any engine gaskets that can cause additional air to enter the crankcase can set this fault as the PCV system is not metered. If a vacuum leak or crankcase gasket sealing is at cause, the idle may be rough or unstable.-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor -GX9-, CHECKING
Filtered lambda controller correction > 35.0 % Filtered lambda controller correction -50.0 - 50.0 % Lambda control active			Throttle position > 4.50° TPS Engine speed > 1, 216; < 6, 000 RPM Modeled pressure quotient > 0.63; < 0.90 [-] Engine running Throttle actuator commanded on Time after engine start > 5.0 s Throttle position sensor failure not detected Fuel cut off not active Fast throttle adaptation finished Gradient intake manifold pressure -199.90 - 199.90 kPa/s Barometric pressure plausibility diagnosis finished And Choice of: MAF sensor active Or Manifold pressure sensor active And Choice of: Pressure upstream throttle < 135.0 kPa Or Pressure upstream throttle not active And Choice of: Barometric pressure > 73.00; < 107.50 kPa Or Barometric pressure sensor not active
P2300 Ignition Coil "A" Primary Control Circuit Low	Ignition Coils Open Circuit	Output voltage in OFF state, lower range >= 1.92 - 2.21 V Output voltage in OFF state, upper range (hardware values) <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
Ignition Coils Short To Ground		Output current in ON state (hardware values) > 50 - 100 mA
Ignition Coils Short To Battery Plus		Diagnosis by inactive low side: switch in ATIC: Output voltage in OFF state (hardware values) > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off
Diagnosis by inactive low side: switch in ATIC: Output temperature from ATIC in ON state > 160.0 - 200.0° C Or Output current in ON state (hardware values) driver stage internal value			Engine speed > 512 RPM Engine stop not active Actuator commanded on
P2303 Ignition Coil "B" Primary Control Circuit Low	Ignition Coils Open Circuit	Output voltage in OFF state, lower range >= 1.92 - 2.21 V Output voltage in OFF state, upper range (hardware values) <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
Ignition Coils Short To Ground		Output current in ON state (hardware values) > 50 - 100 mA
Ignition Coils Short To Battery Plus		Diagnosis by inactive low side: switch in ATIC: Output voltage in OFF state (hardware values) > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off
Diagnosis by inactive low side: switch in ATIC: Output temperature from ATIC in ON state > 160.0 - 200.0° C Or Output current in ON state (hardware values) driver stage internal value			Engine speed > 512 RPM Engine stop not active Actuator commanded on
P2306 Ignition Coil "C" Primary Control Circuit Low	Ignition Coils Open Circuit	Output voltage in OFF state, lower range >= 1.92 - 2.21 V Output voltage in OFF state, upper range (hardware values) <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
Ignition Coils Short To Ground		Output current in ON state (hardware values) > 50 - 100 mA
Ignition Coils Short To Battery Plus		Diagnosis by inactive low side: switch in ATIC: Output voltage in OFF state (hardware values) > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off
Diagnosis by inactive low side: switch in ATIC: Output temperature from ATIC in ON state > 160.0 - 200.0° C Or Output current in ON state (hardware values) driver stage internal value			Engine speed > 512 RPM Engine stop not active Actuator commanded on
P2309 Ignition Coil "D" Primary Control Circuit Low	Ignition Coils Open Circuit	Output voltage in OFF state, lower range >= 1.92 - 2.21 V Output voltage in OFF state, upper range (hardware values) <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
Ignition Coils Short To Ground		Output current in ON state (hardware values) > 50 - 100 mA
Ignition Coils Short To Battery Plus		Diagnosis by inactive low side: switch in ATIC: Output voltage in OFF state (hardware values) > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off
Diagnosis by inactive low side: switch in ATIC: Output temperature from ATIC in ON state > 160.0 - 200.0° C Or Output current in ON state (hardware values) driver stage internal value			Engine speed > 512 RPM Engine stop not active Actuator commanded on
P230A Cylinder 1 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F imbalance: rationality check	Cylinder misfire counter> 2.00[-]	Fuel pressure setpointnot calibratedkPa Modeled catalyst temperature @ start<= 850° C Lambda set value0.97 - 1.03[-] Catalyst heatingnot active Engine roughness signalvalid Fuel cut offnot active AAT>= -48° C Barometric pressure>= 73.00 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosisn.a. Or Catalyst diagnosisn.a. Depending on catalyst diagnosis: Canister purge (conditions)n.a. Or Evap purge valven.a. Or Evap purgen.a. And O2S dynamic diagnosisn.a. O2S delay diagnosisn.a. Lambda controlclosed loop Catalyst purgenot active Canister load<= 2.00[-] Engineno full load Segment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments>= 90.00[-] Segments after start> 0.00[-] Time after engine start> 0.0[s] Rough roadnot detected And Min. fuel mass>= 0.00[mg/rev] Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active And Depending on gear 1st gearnot active 2nd gear not active 3rd gear not active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearnot active And Integrated air mass>= 1.00 - 12.00 kg Diff. engine speed vs. dynamic engine speed< 200 rpm Diff. air mass vs. dynamic air mass< 29.99 mg/rev ECT @ cylinder head60 - 143° C Adaptation cycles<= 255.00[-] Engine speed1, 312 - 3, 008 rpm And Fuel mass setpoint lower range>= 11.00 mg/rev Fuel mass setpoint upper range<= 32.00 mg/rev	90 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P230B Cylinder 2 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F imbalance: rationality check	Cylinder misfire counter> 2.00[-]	Fuel pressure setpointnot calibrated kPa Modeled catalyst temperature @ start<= 850° C Lambda set value0.97 - 1.03[-] Catalyst heatingnot active Engine roughness signalvalid Fuel cut offnot active AAT>= -48° C Barometric pressure>= 73.00 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosisn.a. Or Catalyst diagnosisn.a. Depending on catalyst diagnosis: Canister purge (conditions)n.a. Or Evap purge valven.a. Or Evap purgen.a. And O2S dynamic diagnosisn.a. O2S delay diagnosisn.a. Lambda controlclosed loop Catalyst purgenot active Canister load<= 2.00[-] Engineno full load Sgment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments>= 90.00[-] Segments after start> 0.00[-] Time after engine start> 0.0 s Rough roadnot detected And Min. fuel mass>= 0.00 mg/rev Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active And Depending on gear 1st gearnot active 2nd gearnot active 3rd gearnot active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearnot active And Integrated air mass>= 1.00 - 12.00 kg Diff. engine speed vs. dynamic engine speed< 200 rpm Diff. air mass vs. dynamic air mass< 29.99 mg/rev ECT @ cylinder head60 - 143° C Adaptation cycles<= 255.00[-] Engine speed1, 312 - 3, 008 rpm And Fuel mass setpoint lower range>= 11.00 mg/rev Fuel mass setpoint upper range<= 32.00 mg/rev	90 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P230C Cylinder 3 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F imbalance: rationality check	Cylinder misfire counter> 2.00[-]	Fuel pressure set point not calibratedkPa Modeled catalyst temperature @ start<= 850° C Lambda set value0.97 - 1.03[-] Catalyst heatingnot active Engine roughness signalvalid Fuel cut offnot active AAT>= -48° C Barometric pressure>= 73.00 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosisn.a. Or Catalyst diagnosisn.a. Depending on catalyst diagnosis: Canister purge (conditions)n.a. Or Evap purge valven.a. Or Evap purgen.a. And O2S dynamic diagnosisn.a. O2S delay diagnosisn.a. Lambda controlclosed loop Catalyst purgenot active Canister load<= 2.00[-] Engineno full load Segment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments>= 90.00[-] Segments after start> 0.00[-] Time after engine start> 0.0 s Rough roadnot detected And Min. fuel mass>= 0.00 mg/rev Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active And Depending on gear 1st gearnot active 2nd gearnot active 3rd gearnot active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearnot active And Integrated air mass>= 1.00 - 12.00 kg Diff. engine speed vs. dynamic engine speed< 200rpm Diff. air mass vs. dynamic air mass< 29.99 mg/rev ECT @ cylinder head60 - 143° C Adaptation cycles<= 255.00[-] Engine speed1, 312 - 3, 008 rpm And Fuel mass setpoint lower range>= 11.00 mg/rev Fuel mass setpoint upper range<= 32.00 mg/rev	90 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P230D Cylinder 4 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F imbalance: rationality check	Cylinder misfire counter> 2.00[-]	Fuel pressure setpointnot calibrated kPa Modeled catalyst temperature @ start<= 850° C Lambda set value0.97 - 1.03[-] Catalyst heatingnot active Engine roughness signalvalid Fuel cut offnot active AAT>= -48° C Barometric pressure>= 73.00 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosisn.a. Or Catalyst diagnosisn.a. Depending on catalyst diagnosis: Canister purge (conditions)n.a. Or Evap purge valven.a. Or Evap purgen.a. And O2S dynamic diagnosisn.a. O2S delay diagnosisn.a. Lambda controlclosed loop Catalyst purgenot active Canister load<= 2.00[-] Engineno full load Segment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments>= 90.00[-] Segments after start> 0.00[-] Time after engine start> 0.0 s Rough roadnot detected And Min. fuel mass>= 0.00mg/rev Intake manifold runner flap position changenot active Injection mode change (DFI/MFI)not equipped Valve lift position changenot active And Depending on gear 1st gearnot active 2nd gearnot active 3rd gearnot active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearnot active And Integrated air mass>= 1.00 - 12.00 kg Diff. engine speed vs. dynamic engine speed< 200 rpm Diff. air mass vs. dynamic air mass< 29.99 mg/rev ECT @ cylinder head60 - 143° C Adaptation cycles<= 255.00[-] Engine speed1, 312 - 3, 008 rpm And Fuel mass setpoint lower range>= 11.00 mg/rev Fuel mass setpoint upper range<= 32.00 mg/rev	90 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2414 O2 Sensor Exhaust Sample Error Bank 1 Sensor 1	Oxygen Sensors Front Rationality Check	Pump current correction (nernst-cell) > 1.2 mA	O2S front ready Fuel cut off not active Cylinder shut off not active Depending on engine state: Engine part load Or Engine full load Or Engine idle for time >= 3.0 s	10.0 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter -GX10-, CHECKING .
P2431 AIR System Air Flow/Pressure Sensor Circuit Range/Performance Bank 1	Secondary Air System Pressure Sensor Rationality Check	Difference between AIR pressure and barometric pressure > 6.0 kPa And Difference between AIR pressure and intake manifold pressure > 6.0 kPa	Engine stop For time > 0.0 s	0.1 s Once / DCY	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .
P2432 AIR System Air Flow/Pressure Sensor Circuit Low Bank 1	Secondary Air System Pressure Sensor Out Of Range Low	Sensor voltage < 0.50 V		0.1 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .
P2433 AIR System Air Flow/Pressure Sensor Circuit High Bank 1	Secondary Air System Pressure Sensor Out Of Range High	Sensor voltage > 4.50 V		0.1 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .
P2440 AIR System Switching Valve Stuck Open Bank 1	Secondary Air Valve Functional Check	Ratio relative pressure phase 1 and relative pressure phase 2 > 1.34 [-]	General: Secondary air pump active Catalyst heating active Secondary air injection active MAF <= 140.0 kg/h ECT @ cylinder head >= -10; < 115° C IAT @ manifold >= -10; < 100° C Modeled catalyst temperature < 900° C Relative barometric pressure > 0.73 [-] And Diff. barometric pressure vs. manifold pressure > n.a. kPa Or Engine n.a.	0.1 s Once / DCY	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112-, CHECKING .
P2556 Engine Coolant Level Sensor/Switch Circuit	Rotary Coolant Valve Communication Check	Communication signal failure		0.5 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator -N493-, CHECKING .
Rotary Coolant Valve Signal Check		Sensor signal failure
P2557 Engine Coolant Level Sensor/Switch Circuit Range/Performance	Rotary Coolant Valve Checksum Verification	Checksum signal failure		0.5 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator -N493-, CHECKING .
P2564 Turbocharger Boost Control Position Sensor "A" Circuit Low	Turbocharger Boost Control Position Sensor Short To Ground / Open Circuit	Turbocharger boost control position sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- Check the Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-. Refer to Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-, CHECKING ..
P2565 Turbocharger Boost Control Position Sensor "A" Circuit High	Turbocharger Boost Control Position Sensor Short To Battery Voltage	Turbocharger boost control position sensor voltage > 4.80 V		0.5 s Continuous	2 DCY	-- Check the Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-. Refer to Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-, CHECKING .
P2610 ECM/PCM Engine Off Timer Performance	Engine Off Time ECM Internal Timer Check	ECM internal timerfailure Or ECM internal timer signalnot calibrated ECM internal timernot calibrated Time after last engine stop not calibrated	SPI initialization finished	1.3 s Continuous	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
Engine Off Time ECM Rationality Check		Difference between engine-off-time and ECM keep alive-time >= 12.0 s Or Difference between ECM keep alive-time and engine-off-time>= 12.0s	Monitor Entry Conditions: ECM keep alive-time active ECU internal timer reset not activated Time delay >= 1.0 s Time after last engine stop< 48[h] Case 1: For time (after entry conditions fulfilled)>= 65 s Case 2: For time (after entry conditions fulfilled)< 65 s Ignition keytransition off to on	10 ms Once / DCY
Difference between engine-off-time and ECM keep alive-time >= 12.0 s			Time after engine stop < 86, 400.0 s Engine off time plausible Engine off time monitoring not finished Engine off time signal valid time after reset < 2.0 s And Case 1: Engine off timer n.a. Or Engine off time n.a. Case 2: ECM internal timer active SPI communication failure after reset detected
P2635 Fuel Pump Control Module Performance	COM: Fuel Pump Control Module (FPCM) communication with FPCM	FP signal: overcurrent failure feedback>= 2.00[-]	Engine on	1.6 s Continuous	2 DCY	-- Check the Fuel Pump Control Module -J538-. Refer to Fuel Pump Control Module -J538- /Fuel Delivery Unit -GX1-, CHECKING
			FP signal: rotary failure feedback>= 2.00[-]			1.8 s Continuous
			FP sensor: short to battery failure or rpm deviation feedback>= 2.00[-]			2.4 s Continuous
P2681 Engine Coolant Bypass Valve "A" Control Circuit/Open	Rotary Coolant Valve Open Circuit	Load resistance > 200.0 kOhm	Rotary slide valve commanded off	1.3 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator -N493-, CHECKING ..
P2682 Engine Coolant Bypass Valve "A" Control Circuit Low	Rotary Coolant Valve Short To Ground Output 1	High side current output 1 driver stage internal value	Rotary slide valve commanded on Rotary valve direction forward	0.30 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator -N493-, CHECKING .
Rotary Coolant Valve Short To Ground Output 2		High side current output 2 driver stage internal value	Rotary slide valve commanded on Rotary valve direction reversed
P2683 Engine Coolant Bypass Valve "A" Control Circuit High	Rotary Coolant Valve Short To Battery Plus Output 1	Low side current output 1 driver stage internal value	Rotary slide valve commanded off	0.30 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator -N493-, CHECKING .
Rotary Coolant Valve Short To Battery Plus Output 2		Low side current output 2 driver stage internal value	Rotary slide valve commanded off
P334A Charge Pressure Actuator Electrical Error	Turbocharger Boost Pressure Control Valve Short To Ground	Bypass valve driver current driver stage internal value	Boost pressure actuator controller active	0.4 s Continuous	2 DCY	-- Check the Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-. Refer to Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-, CHECKING .
U0001 High Speed CAN Communication Bus	CAN: Powertrain BUS reading back sent message Powertrain	Message no feedback	Time after ignition on 0.5 s	0.5 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U0002 High Speed CAN Communication Bus Performance	CAN: Powertrain BUS communication check Powertrain	Global time outreceiving no message	Time after ignition on 0.5 s	0.5 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U0101 Lost Communication with TCM	CAN: Transmission Control Module (TCM) CAN Communication With TCM	Received message from TCM no message	Time after ignition on 0.5 s	1.0 s	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U0121 Lost Communication With Anti-Lock Brake System (ABS) Control Module	CAN: Brake System Control Module (BSCM) communication with BSCM	Received CAN message no message	Time after ignition on 0.5 s	0.5 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U0140 Lost Communication With Body Control Module	CAN: Body Control Module (BCM) CAN Communication With Body Control Module	Received CAN message no message	Time after ignition on 0.5 s	2.0 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U0146 Lost Communication With Gateway "A"	CAN: Gateway CAN Communication With Gateway	Message no message	Time after ignition on 0.5 s	1.0 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module	CAN: Instrument Cluster CAN Communication With Instrument Cluster Module	Message no message	Time after ignition on 0.5 s	5.0 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U0302 Software Incompatibility With Transmission Control Module	COM: Transmission Control Module (TCM) communication with TCM	Received AT vehicle data from TCM, TCM signal	Time after ignition on0.5 s	5.0 s Continuous	2 DCY	-- Check for software updates and TSB's. Reprogram as necessary. If none are found, refer to appropriate repair information.
U0322 Software Incompatibility With Body Control Module	CAN: Gateway CAN Communication With Gateway	Ambient temperature sensor coding monitoring failure	Time after ignition on > 1.5 s	2.0 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first. -- Refer to the proper wiring schematic for terminal and component location.
U0415 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module	Vehicle Speed Rationality Check High	Vehicle speed > 202 mph		2.0 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first. -- Refer to appropriate repair information for the ABS.-- Refer to the proper wiring schematic for terminal and component location.
CAN: Vehicle Speed Sensor CAN communication with BSCM		Speed sensor signal: sensor error=655, 35km/h (no map, just bottom and top limit)	Time since engine on > 0.5 s	0.5 s Continuous
Speed sensor signal: initialization error=655, 33 - 655, 34 km/h (no map, just bottom and top limit)			Time since engine on > 0.5 s Vehicle speed < 7 mph	2.0 s Continuous
speed sensor signal: low voltage error=655, 33 - 655, 34km/h (no map, just bottom and top limit)			Time since engine on > 0.5 s Vehicle speed > 7 mph	0.5 s Continuous
CAN: Brake System Control Module (BSCM) CAN Communication With Brake Unit		Received data from TCS implausible message	Time after ignition on 0.5 s	0.5 s Continuous
U0422 Invalid Data Received From Body Control Module	CAN: Gateway CAN communication with BCM	Received data from BCMimplausible message	Time after ignition on 0.5 s	1.0 s Continuous	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor -G17-, CHECKING .-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
Ambient temperature value (initialization)failure			Time after ignition on> 1.5 s Enginerunning	3.0 s Continuous	2 DCY
U0423 Invalid Data Received From Instrument Panel Cluster Control Module	CAN: Instrument Cluster CAN Communication With Instrument Cluster Module	Received data from Instrument Cluster implausible message	Time after ignition on 0.5 s	3.0 s Continuous	2 DCY	-- Check the CAN-Bus circuits. If there are any other DTC's present check them first.-- Refer to the proper wiring schematic for terminal and component location.
U1103 Production Mode Active	ECM: Production Mode Function Monitoring: Mode Change	Production mode active	Vehicle speed < 3 mph Max trip mileage since initial vehicle start-up < 62.15 miles During ECM keep alive-time after ignition off engine speed 0 rpm For hybrid: Drive motor off	0.01 s Continuous	1DCY	-- PERFORM: Preliminary Check to verify the concern. Refer to PRELIMINARY CHECK .-- Perform readiness check. Refer to READINESS CODES .