Test Procedure

NOTE:

When The Door Is Opened Or The Ignition Is Turned To The ON Position The Fuel Pump Is Activated For 2 Seconds To Build Up The Pressure In The Fuel System.

Step	Procedure	Result / Action to Take
1	PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK . -- Was Complaint verified?	-- YES: GO TO: Step 2 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 3 . NO: GATHER more Information from customer about the complaint.
2	IGNITION: ON. LISTEN: Fuel Delivery Unit -GX1- Should be heard running for 2 s. SPECIFIED VALUE: Transfer Fuel Pump ON for 2 s. IGNITION: OFF. -- Was Value obtained?	-- YES: Condition may be intermittent. PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 7 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 7 . NO: GO TO: Step 3 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 3 .
3	IGNITION: OFF. DISCONNECT: Fuel Pump Control Module. -J538- IGNITION: ON. CHECK: Fuel Pump Control Module -J538- harness connector terminals 5 to 4 for voltage. CHECK: Fuel Pump Control Module -J538- harness connector terminal 4 to battery voltage for voltage. SPECIFIED VALUE: Battery voltage. IGNITION: OFF. -- Were Values obtained?	-- YES: GO TO: Step 4 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 4 . NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 7 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 7 .
4	RECONNECT: Fuel Pump Control Module -J538-. DISCONNECT: Fuel Delivery Unit -GX1-. CRANK: Engine. CHECK: Fuel Delivery Unit -GX1- harness connector terminals 2 to 4 for voltage while engine is cranking. IGNITION: OFF. SPECIFIED VALUE: 7 - 11 V. -- Was Value obtained?	-- YES: REPLACE: Fuel Delivery Unit -GX1-, Refer to appropriate service information. GO TO: Step 7 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 7 . NO: GO TO: Step 5 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 5 .
5	DISCONNECT: Fuel Pump Control Module -J538-. CHECK: Fuel Delivery Unit -GX1- harness connector terminal 2 to Fuel Pump Control Module -J538- wiring connector 2 for resistance. CHECK: Fuel Delivery Unit -GX1- harness connector terminal 3 to Fuel Pump Control Module -J538- wiring connector 1 for resistance. CHECK: Fuel Delivery Unit -GX1- harness connector terminal 1 to Fuel Pump Control Module -J538- wiring connector 3 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Were values obtained?	-- YES: GO TO: Step 6 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 6 . NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 7 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 7 .
6	REMOVE: Engine Control Module -J623-. Refer to appropriate service information. CHECK: Fuel Pump Control Module -J538- harness connector terminal 6 to Engine Control Module -J623- wiring connector terminal T94 / 76 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Were values obtained?	-- YES: GO TO: Step 7 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 7 . NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 7 Fuel Pump Control Module - J538- / Fuel Delivery Unit -GX1-, CHECKING - 7 .
7	Refer To The Final Procedure Below;