Flash: Park Assist Module (PAM) Compatibility Updates (08-067-19)

Publication date: 2019-06-22
Reference number: 08-067-19

FLASH: PARK ASSIST MODULE (PAM) COMPATIBILITY UPDATES

TECHNICAL SERVICE BULLETIN

Reference Number(s): 08-067-19, Date of Issue: June 22, 2019

CHRYSLER:	2017-2018 Alfa Romeo Stelvio (GA)
GROUP:	08 - Electrical

OVERVIEW

This bulletin involves reprogramming the PAM with the latest available software.

MODELS

MODELS CHART

2018

(GU)

Alfa Romeo Stelvio

NOTE: This bulletin applies to vehicles within the following markets/countries: North America.

NOTE: This bulletin applies to vehicles built on or before April 12, 2018 (MDH 0412XX) equipped with ParkSense FT/RR Park Assist System (Sales Code XAG) or Parksense Rear Park Assist System (Sales Code XAA).

SYMPTOM/CONDITION

If the vehicle was equipped with a version 2.0 Entertainment Telematics Module (ETM) and the ETM was replaced with a version 2.5, this software update needs to be performed in order to make the PAM compatible with the new ETM.

If the ETM was not replaced or updated to version 2.5 no further action is needed do not update the PAM at this time.

DIAGNOSIS

Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If Diagnostic Trouble Codes (DTCs) or symptom conditions, other than the ones listed above are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin.

If the technician finds the ETM was replaced or updated to version 2.5 per the symptom/condition listed above, perform the Repair Procedure.

REPAIR PROCEDURE

CAUTION: If the ETM has been replaced with a version 2.5, it will require updating and/or be at a minimum software level of A85 (Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the ETM). After the ETM replacement and software update to a minimum level of A85, all of the following modules MUST be updated:

Body Control Module (BCM)
Amplifier (AMP)
Antilock Brake System (ABS)
Instrument Panel Cluster (IPC)
Park Assist Module (PAM)
Left Blind Spot Sensor (LBSS)/Right Blind Spot Sensor (RBSS)

Failure to update all modules following an PAM replacement and/or software update may result in vehicle malfunctions.

CAUTION: If the PAM has been replaced, or if the PAM software is updated, the ETM MUST be at version 2.5 and at a minimum software level of A85 (Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the ETM). After the PAM replacement and/or software update, all of the following modules MUST be updated:

Body Control Module (BCM)
Amplifier (AMP)
Antilock Brake System (ABS)
Instrument Panel Cluster (IPC)
Entertainment Telematics Module (ETM)
Left Blind Spot Sensor (LBSS)/Right Blind Spot Sensor (RBSS)

Failure to update all modules following an PAM replacement and/or software update may result in vehicle malfunctions.

NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2 volts. Do not allow the charging voltage to climb above 13.5 volts during the flash process.

NOTE: If this flash process is interrupted/aborted, the flash should be restarted.

Reprogram the PAM with the latest available software. Detailed instructions for flashing control modules using the wiTECH Diagnostic Application are available by selecting the application's "HELP" tab.
Verify the BCM is programmed with the latest available software. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the BCM software.
Verify the ETM is programmed with the latest available software. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the ETM software.
Verify the ABS module is programmed with the latest available software. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the ABS software.
Verify the LBSS/RBSS is programmed with the latest available software. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the LBSS/RBSS software.
Verify the IPC is programmed with the latest available software. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the IPC software.
Verify the AMP is programmed with the latest available software. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the AMP software.
Clear all DTCs that may have been set in any module due to reprogramming. The wiTECH application will automatically present all DTCs after the flash and allow them to be cleared.

POLICY

Reimbursable within the provisions of the warranty.

TIME ALLOWANCE

TIME ALLOWANCE CHART

Labor Operation No:	Description	Skill Category	Amount
18-20-05-9G	Module, Park Assist Control (PAM) - Reprogram (0 - Introduction)	6 - Electrical and Body Systems	0.2 Hrs.

NOTE: The expected completion time for the flash download portion of this procedure is approximately 2 minutes. Actual flash download times may be affected by vehicle connection and network capabilities.

FAILURE CODE

The dealer must use failure code CC with this Service Bulletin.

If the customer's concern matches the SYMPTOM/CONDITION identified in the Service Bulletin, failure code CC is to be used.
When utilizing this failure code the 3C's (customer's concern, cause and correction) must be provided for processing Service Bulletin flash/reprogramming conditions.

FAILURE CODE CHART

CC	Customer Concern