Torque Specifications
ENGINE BLOCK
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Balance Shaft to Engine Block Screw | 10 | 7 | - | |
| Connecting Rod M9 Cap Bolts | 20 + 100° | 15 + 100° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Main Bearing Bolts | ||||
| M10 Cap Bolts | 14 + 45 + 90° | 10 + 33 + 90° | - | Tighten in sequence. Refer to CRANKSHAFT, REMOVAL AND INSTALLATION . |
| M8 Tie Bolts | 23 | 17 | - | |
| Crankshaft Target Ring Screws | 12 | 9 | - | |
CYLINDER HEAD
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Camshaft Position Sensor Stud Bolt | 9 | - | 80 | |
| Cylinder Head Bolts | ||||
| Inner M11 Bolts | 55 + 180° | 41 + 180° | - | Tighten in sequence. Refer to CYLINDER HEAD, REMOVAL AND INSTALLATION |
| Side M8 Bolt | 28 | 21 | - | |
| Cylinder Head Cover M6 Bolts | 10 | - | 89 | |
| Coolant Manifold M6 Bolts | 11 | - | 97 | |
| Camshaft Cap M6 Bolts | 10 | - | 89 | |
| High Pressure Fuel Pump M6 Nuts | 11 | - | 97 | |
| Spark Plugs | 20 | 15 | - | |
| Variable Valve Actuation Assembly (VVAA) M8 Bolts | 23 | 17 | - | Tighten in sequence. Refer to CYLINDER HEAD, REMOVAL AND INSTALLATION . |
| Intake Manifold M6 Bolts | 11 | - | 97 | |
FRONT ENGINE
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Timing Cover to Crankcase and Cylinder Head M6 Bolts | 9 | - | 80 | Tighten in sequence. Refer to ASSEMBLY, VARIABLE VALVE ACTUATION, REMOVAL AND INSTALLATION . |
| Cam Chain Tensioner M6 Bolts | 9 | - | 80 | |
| Oil Pump Drive Chain Tensioner M6 Bolts | 9 | - | 80 | |
| Camshaft Sprocket Bolt | 10 + 65° | - | 89 + 65° | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Oil Pump Sprocket M8 Bolt | 15 + 40° | 11 + 40° | - | |
| Cam Chain Guide M8 Bolts | 22 | 16 | - | |
| Cam Chain Tensioner Arm M8 Bolt | 28 | 21 | - | |
| Oil Pump Drive Chain Guide M6 Bolts | 10 | - | 89 | |
| Vibration Damper M14 Bolt | 50 + 68° | 37 + 68° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
REAR ENGINE
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Flexplate M12 Bolts | 110 | 81 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Rear Crankshaft Oil Seal Retainer Bolts | 10 | - | 89 | Tighten in sequence. Refer to SEAL, CRANKSHAFT OIL, REAR, REMOVAL AND INSTALLATION |
| Transmission Bolts | 55 | 41 | - | |
| Transmission Nuts | 55 | 41 | - | |
| Torque Converter Bolts | 41 | 30 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
ENGINE MOUNTS
| Description | Nm | Ft Lbs | In Lbs | Comment |
|---|---|---|---|---|
| Right and Left front engine mount bracket M10 bolts | 10 + 45° | - | 89 + 45° | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Front engine mount crossmember bolts | 64 | 47 | - | |
| Right and Left front engine mount insulator M10 bolts | 65 | 89 | - | |
| Right and Left front engine mount insulator M12 nuts | 120 | 89 | - | |
| Rear engine/transmission mount lower bracket to body M10 bolts FWD | 20 + 45° | 15 + 45° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Rear engine/transmission mount lower bracket to body M10 bolts AWD | 30 + 45° | 22 + 45° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Rear engine/transmission insulator to lower bracket M8 nuts RWD | 28 | 21 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Rear engine/transmission insulator to upper bracket M8 nuts RWD | 28 | 21 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Rear engine/transmission upper bracket to transmission M10 bolts FWD | 50 | 37 | - | |
| Rear engine/transmission mount insulator to transfer case M14 bolt AWD | 130 | 96 | - |
LUBRICATION
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Engine Oil Cooler M6 Screws | 12 | 9 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Engine Oil Drain M14 Plug | 20 | 15 | - | |
| Oil Filter | 13 | 10 | - | |
| Oil Vapor Separator M6 Bolts | 9 | - | 80 | Tighten in sequence. Refer to SEPARATOR, OIL, REMOVAL AND INSTALLATION . |
| Oil Pressure/Temperature Sensor | 50 | 37 | - | |
| Oil Temperature Sensor (VVAA) | 11 | - | 97 | |
| Piston Oil Cooler Jet | 11 | - | 97 | |
| Windage Tray | 10 | - | 89 | Tighten in sequence. Refer to PAN, OIL, REMOVAL AND INSTALLATION |
| Oil Pick-up Tube | 11 | - | 97 | |
| Oil Pan Bolts | ||||
| M6 | 9 | - | 80 | Tighten in sequence. Refer to PAN, OIL, REMOVAL AND INSTALLATION . |
| M8 | 25 | 18 | - | |
| M10 | 55 | 41 | - | |
| Oil Pump M6 Bolts | 9 | - | 80 | |
| Oil Pump Displacement Control Solenoid Studbolt | 8 | - | 71 | |
| Oil Gallery Pipe Plugs | ||||
| M10 Plug | 4 + 450° | - | 35 + 450° | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| M12 Plug | 30 | 20 | - | |
| M14 Plug | + 1.5 mm to - 0.5 mm (+ 0.06 In. to - 0.02 In.) flush with the block boss face | |||
| M18 Plug | + 1.5 mm to - 0.5 mm (+ 0.06 In. to - 0.02 In.) flush with the block boss face | |||
TURBOCHARGER
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Turbocharger to Cylinder Head M8 Nuts | 25 | 18 | - | Do not reuse these fasteners. If removed, a NEW
fastener must be installed and tightened to specifications. Tighten in sequence. Refer to TURBOCHARGER, REMOVAL AND INSTALLATION . |
| Turbocharger Heat Shield M6 Bolts | 9 | - | 80 | |
| Turbocharger Heat Shield M6 Nut | 9 | - | 80 | |
| Intake Bypass Pipe Connector to Turbocharger M6 Bolts | 13 | 10 | - | |
| Turbocharger Air Outlet Pipe to Cylinder Head Cover M6 Bolt | 8 | - | 71 | |
| Turbocharger Air Outlet Hose Clamps | 5.5 | - | 49 | |
| Throttle Body Air Inlet Hose Clamps | 5.5 | - | 49 | |
| Turbocharger Coolant Supply Pipe to Turbocharger M6 Bolt | 9 | - | 80 | |
| Turbocharger Coolant Return Pipe to Turbocharger M6 Bolt | 9 | - | 80 | |
| Turbocharger Oil Supply Pipe to Turbocharger M6 Bolt | 11 | - | 97 | |
| Turbocharger Oil Supply Pipe to Crankcase M6 Bolt | 11 | - | 97 | |
| Turbocharger Oil Return Pipe to Turbocharger M6 Bolt | 11 | - | 97 | |
| Turbocharger Oil Return Pipe to Crankcase M6 Bolts | 11 | - | 97 |